where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
976 views
Technical Discussions
David Mackintosh
Engineering,
Acuren Group Inc., Canada, Joined Feb 2011, 85

David Mackintosh

Engineering,
Acuren Group Inc.,
Canada,
Joined Feb 2011
85
08:23 Dec-12-2008
Code Case 2235 examination volume



Code Case 2235 paragraph (a) requires that for t<= 8 inch the examination include the volume of the weld plus the lesser of 1 inch or t on each side of the weld.

In most cases this would require additional TOFD scans with the probe pair offset (see sketch), which in turn might require the weld cap to be ground flat. In other words, it is very difficult to cover the required volume using TOFD alone.

In practice, I believe many NDT examiners are carrying out TOFD without worrying about covering the edges of the examination volume. Can anyone confirm this? Or are there examiners who make the extra effort to cover the entire zone?

Supplemental UT is used to cover the TOFD dead zones. Perhaps supplemental UT should also be used to cover the entire width of the examination volume, thus removing the necessity of grinding the weld cap flat for TOFD.

Thanks,
David Mackintosh


 
 Reply 
 
Manfred Richter
Consultant,
Richter & Tomasi Ltd., Brazil, Joined Jan 2008, 31

Manfred Richter

Consultant,
Richter & Tomasi Ltd.,
Brazil,
Joined Jan 2008
31
00:03 Dec-12-2008
Re: Code Case 2235 examination volume
Code Case 2235-9, and now ASME VIII Div.2 Part 7 states that "Alternatively, examination volume may be reduced to include the actual heat affected zone (HAZ) plus 6 mm (1/4 in) of base material beyond the heat affected zone on each side of the weld..." . As the welds shall be approved through a WPS and macros should be done, the HAZ could be measured and the additional scan avoided. I think this is one of the reason to not do additional or Y scan.
Regards,
Manfred


----------- Start Original Message -----------
: Code Case 2235 paragraph (a) requires that for t<= 8 inch the examination include the volume of the weld plus the lesser of 1 inch or t on each side of the weld.
: In most cases this would require additional TOFD scans with the probe pair offset (see sketch), which in turn might require the weld cap to be ground flat. In other words, it is very difficult to cover the required volume using TOFD alone.
: In practice, I believe many NDT examiners are carrying out TOFD without worrying about covering the edges of the examination volume. Can anyone confirm this? Or are there examiners who make the extra effort to cover the entire zone?
: Supplemental UT is used to cover the TOFD dead zones. Perhaps supplemental UT should also be used to cover the entire width of the examination volume, thus removing the necessity of grinding the weld cap flat for TOFD.
: Thanks,
: David Mackintosh
------------ End Original Message ------------




 
 Reply 
 
mj
mj
04:08 Dec-13-2008
Re: Code Case 2235 examination volume

Hello David,
u are right most of the people not taking care the edge. also please note that we can cover entire volume with 2 pair TOFD probes. I did 100 mm thick CS sphere with 2 pair TOFD probes. We need to make a notch in the HAZ opposite side of the probes. if you will not get you have to go for 1 set of creeping probes for TOP surface and 1 set of 45% angle shear wave for back surface.
Thanks
MJ





 
 Reply 
 

Product Spotlight

NovaScope 6000

The all-digital Novascope 6000 is a portable, ultra-high precision thickness gauge for high-speed
...
thickness measurement. Novascope 6000 has unmatched capabilities and unique features including: •Superior Resolution with high contrast, high-speed color RF display •High pulser voltage •Real-time video output •Increased internal/external data storage •Programmable SetUp features •Battery & AC Powered
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Navic - Steerable Modular Automated Scanner

The Navic is a modular, motorized, steerable scanner designed to carry multiple attachments used
...
in various scanning and inspection applications. The Navic is capable of weld scanning (girth welds and long seam welds), automated corrosion mapping, and tank scanning.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window