where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

VOGT Ultrasonics GmbH
non-destructive testing, services, training, ultrasonic systems, immersion and squirter inspection systems, PROline, digital radiology
2738 views
Technical Discussions
Kumar
Kumar
03:48 Aug-25-2008
ASME Code Case 2235 Qualification blocks

Could anyone tell me where can I have the UT qualification/demonstration blocks made to ASME Code case 2235? The flaws are supposed to be actual flaws generated by welding.

Thks!


    
 
 Reply 
 
mj
mj
00:08 Aug-26-2008
Re: ASME Code Case 2235 Qualification blocks
Dear Friend, as per code case 2235-09 qualification block shall be prepared by welding or HIP and ahll contain 3 flaws( it maybe a diffect or notch/side drilled hole. the diffrence between both calibration and qualification block is, one made just in a plate and other in a welding, also usualy if u make a small thickness qualificatin block during welding u can keep some welding rod inside and weld. also you can keep a RT report for the block. iam sure flaw maybe a natural defect or artificial!!!! always iam making this kind of blocks
Please let me know others comment. if iam not right please respond.

mj


----------- Start Original Message -----------
: Could anyone tell me where can I have the UT qualification/demonstration blocks made to ASME Code case 2235? The flaws are supposed to be actual flaws generated by welding.
: Thks!
------------ End Original Message ------------




    
 
 Reply 
 
mustafa GONULAL
Engineering,
CIMTAS / ENKA, Turkey, Joined Jun 2008, 8

mustafa GONULAL

Engineering,
CIMTAS / ENKA,
Turkey,
Joined Jun 2008
8
00:49 Aug-27-2008
Re: ASME Code Case 2235 Qualification blocks
Dear peers,
I am drawing and producing calibration and qualification blocks over 4 years. If you want to know more detail contact with me via e-mail.

----------- Start Original Message -----------
: Dear Friend, as per code case 2235-09 qualification block shall be prepared by welding or HIP and ahll contain 3 flaws( it maybe a diffect or notch/side drilled hole. the diffrence between both calibration and qualification block is, one made just in a plate and other in a welding, also usualy if u make a small thickness qualificatin block during welding u can keep some welding rod inside and weld. also you can keep a RT report for the block. iam sure flaw maybe a natural defect or artificial!!!! always iam making this kind of blocks
: Please let me know others comment. if iam not right please respond.
: mj
:
: : Could anyone tell me where can I have the UT qualification/demonstration blocks made to ASME Code case 2235? The flaws are supposed to be actual flaws generated by welding.
: : Thks!
------------ End Original Message ------------




    
 
 Reply 
 
Michael Moles †2014 *1948
, Joined ,
02:44 Aug-28-2008
Re: ASME Code Case 2235 Qualification blocks
----------- Start Original Message -----------
: Dear peers,
: I am drawing and producing calibration and qualification blocks over 4 years. If you want to know more detail contact with me via e-mail.
: : Dear Friend, as per code case 2235-09 qualification block shall be prepared by welding or HIP and ahll contain 3 flaws( it maybe a diffect or notch/side drilled hole. the diffrence between both calibration and qualification block is, one made just in a plate and other in a welding, also usualy if u make a small thickness qualificatin block during welding u can keep some welding rod inside and weld. also you can keep a RT report for the block. iam sure flaw maybe a natural defect or artificial!!!! always iam making this kind of blocks
: : Please let me know others comment. if iam not right please respond.
: : mj
: :
: : : Could anyone tell me where can I have the UT qualification/demonstration blocks made to ASME Code case 2235? The flaws are supposed to be actual flaws generated by welding.
: : : Thks!
------------ End Original Message ------------

Unfortunately, you are not correct in your interpretation. While the original ASME CC 2235 was not clear on this issue, the intent was to use artificial cracks - not side drilled holes or notches - as the reflectors. In addition, the artificial cracks should follow the bevel to simulate Lack of Fusion defects or similar. ASME is currently working on clarifying this situation.

Michael Moles
Member, ASME Section V Ultrasonics Working Group



    
 
 Reply 
 
mj
mj
09:04 Aug-30-2008
Re: ASME Code Case 2235 Qualification blocks
----------- Start Original Message -----------
: : Dear peers,
: : I am drawing and producing calibration and qualification blocks over 4 years. If you want to know more detail contact with me via e-mail.
: : : Dear Friend, as per code case 2235-09 qualification block shall be prepared by welding or HIP and ahll contain 3 flaws( it maybe a diffect or notch/side drilled hole. the diffrence between both calibration and qualification block is, one made just in a plate and other in a welding, also usualy if u make a small thickness qualificatin block during welding u can keep some welding rod inside and weld. also you can keep a RT report for the block. iam sure flaw maybe a natural defect or artificial!!!! always iam making this kind of blocks
: : : Please let me know others comment. if iam not right please respond.
: : : mj
: : :
: : : : Could anyone tell me where can I have the UT qualification/demonstration blocks made to ASME Code case 2235? The flaws are supposed to be actual flaws generated by welding.
: : : : Thks!
: Unfortunately, you are not correct in your interpretation. While the original ASME CC 2235 was not clear on this issue, the intent was to use artificial cracks - not side drilled holes or notches - as the reflectors. In addition, the artificial cracks should follow the bevel to simulate Lack of Fusion defects or similar. ASME is currently working on clarifying this situation.
: Michael Moles
: Member, ASME Section V Ultrasonics Working Group
------------ End Original Message ------------

Thanks Michael we are only using code case 2235-09 or asme sec.V for the inspection . sure i did atleast 25 project using the same code and with a normal demo block. if something diffrent come out from ASME we will follow it
MJ


    
 
 Reply 
 
EC
EC
00:09 Sep-10-2008
Re: ASME Code Case 2235 Qualification blocks
----------- Start Original Message -----------
: : : Dear peers,
: : : I am drawing and producing calibration and qualification blocks over 4 years. If you want to know more detail contact with me via e-mail.
: : : : Dear Friend, as per code case 2235-09 qualification block shall be prepared by welding or HIP and ahll contain 3 flaws( it maybe a diffect or notch/side drilled hole. the diffrence between both calibration and qualification block is, one made just in a plate and other in a welding, also usualy if u make a small thickness qualificatin block during welding u can keep some welding rod inside and weld. also you can keep a RT report for the block. iam sure flaw maybe a natural defect or artificial!!!! always iam making this kind of blocks
: : : : Please let me know others comment. if iam not right please respond.
: : : : mj
: : : :
: : : : : Could anyone tell me where can I have the UT qualification/demonstration blocks made to ASME Code case 2235? The flaws are supposed to be actual flaws generated by welding.
: : : : : Thks!
: : Unfortunately, you are not correct in your interpretation. While the original ASME CC 2235 was not clear on this issue, the intent was to use artificial cracks - not side drilled holes or notches - as the reflectors. In addition, the artificial cracks should follow the bevel to simulate Lack of Fusion defects or similar. ASME is currently working on clarifying this situation.
: : Michael Moles
: : Member, ASME Section V Ultrasonics Working Group
: Thanks Michael we are only using code case 2235-09 or asme sec.V for the inspection . sure i did atleast 25 project using the same code and with a normal demo block. if something diffrent come out from ASME we will follow it
: MJ
------------ End Original Message ------------

Hello, we are working with TOFD inspection procedures following ASME V and VIII and we've a problem with the interpretation of the qualification block's thickness. Could somebody explain us what thickness we must choose for a range of inspection of 25 to 200 mm?
thanks!!!!


    
 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
01:17 Sep-10-2008
Re: ASME Code Case 2235 Qualification blocks
Hi EC

You should read the 2007 Edition of ASME V, Article 4 Mandatory Appendix III, TOFD of welds. Calibration block thickness and range qualified are clearly stated in III-434.

Regards

Nigel

----------- Start Original Message -----------
: : : : Dear peers,
: : : : I am drawing and producing calibration and qualification blocks over 4 years. If you want to know more detail contact with me via e-mail.
: : : : : Dear Friend, as per code case 2235-09 qualification block shall be prepared by welding or HIP and ahll contain 3 flaws( it maybe a diffect or notch/side drilled hole. the diffrence between both calibration and qualification block is, one made just in a plate and other in a welding, also usualy if u make a small thickness qualificatin block during welding u can keep some welding rod inside and weld. also you can keep a RT report for the block. iam sure flaw maybe a natural defect or artificial!!!! always iam making this kind of blocks
: : : : : Please let me know others comment. if iam not right please respond.
: : : : : mj
: : : : :
: : : : : : Could anyone tell me where can I have the UT qualification/demonstration blocks made to ASME Code case 2235? The flaws are supposed to be actual flaws generated by welding.
: : : : : : Thks!
: : : Unfortunately, you are not correct in your interpretation. While the original ASME CC 2235 was not clear on this issue, the intent was to use artificial cracks - not side drilled holes or notches - as the reflectors. In addition, the artificial cracks should follow the bevel to simulate Lack of Fusion defects or similar. ASME is currently working on clarifying this situation.
: : : Michael Moles
: : : Member, ASME Section V Ultrasonics Working Group
: : Thanks Michael we are only using code case 2235-09 or asme sec.V for the inspection . sure i did atleast 25 project using the same code and with a normal demo block. if something diffrent come out from ASME we will follow it
: : MJ
: Hello, we are working with TOFD inspection procedures following ASME V and VIII and we've a problem with the interpretation of the qualification block's thickness. Could somebody explain us what thickness we must choose for a range of inspection of 25 to 200 mm?
: thanks!!!!
------------ End Original Message ------------




    
 
 Reply 
 
David Mackintosh
Engineering,
Acuren Group Inc., Canada, Joined Feb 2011, 85

David Mackintosh

Engineering,
Acuren Group Inc.,
Canada,
Joined Feb 2011
85
08:54 Dec-12-2008
Re: ASME Code Case 2235 Qualification blocks
----------- Start Original Message -----------
: Hi EC
: You should read the 2007 Edition of ASME V, Article 4 Mandatory Appendix III, TOFD of welds. Calibration block thickness and range qualified are clearly stated in III-434.
: Regards
: Nigel
-------------------------------------------------

I believe that Appendix III only specifies the CALIBRATION block. For the QUALIFICATION block, Code Case 2235 only requires the three flaws and says very little about the block design. It is up to the Owner to design a qualification/demonstration block specific to their needs.

David


    
 
 Reply 
 

Product Spotlight

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

GUL QSR1® Scanning

How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav
...
e Quantitative Short Range Scanning.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window