where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

414 views
Technical Discussions
Kelly Schauf
Kelly Schauf
08:13 Aug-18-1998
Non destructive isolation of PC-mount Transformer short

To the forum:

Currently, I am testing a printed-circuit-board-mount transformer.
There is one primary winding and three secondary windings.
There are two powdered-iron 'E' cores that are epoxied
together around the bobbin to provide the core for the transformer.

I have a problem where the inductance and the Q of the primary coil
drop way below normal past 1500 Hz with a signal of 100millivolts AC
applied. I suspect that there is a shorted turn of wire that may be causing
this.

Generally, there is maybe 1000+ turns of wire on the transformer, and the
chances of finding a marginal short-circuit with merely a microscope and
the eyes is a 'needle-in-a-haystack' type of chance. Is there some
method that would incorporate an electrical signal that would enable me
to find a short-circuit in the primary winding?

Any and all ideas are welcome. Questions are also welcome.

Regards,

Kelly Schauf


 
 Reply 
 
Jeff Nelson
Jeff Nelson
07:44 Jun-28-2000
Re: Non destructive isolation of PC-mount Transformer short
r this may help you locate how far down the line the short is.



 
 Reply 
 
Jamie Gauthier
Jamie Gauthier
09:33 Jul-01-2000
Re: Non destructive isolation of PC-mount Transformer short
In response to the TDR message post. Time Domain Reflectometer works well
but has several disadvantages. The instrument works well as long as you
have the mininum length of cable to measure. TDR's have a dead zone. This
dead zone can range from 25 to 50 feet (plus or minus depending on the
quality of your instrument.) Do you have another transformer with an equal
number of turns? If so then you can reference the value of one against the
other using a TDR. The TDR I have been using lately has an error of + or -
1% of the total length of the cable. When you are dealing with transformers
this is very large and usually unaccpetable. Once you find the short then
what? Are you equipped to hand wind it? Good luck with you
trouble-shooting. Regards,


Jamie Gauthier
Field Service Electronics Technician
Toll Free: 800-661-0066
Fax: 780-440-2538
Cell: 780-940-3427
Pager: 780-431-7470
E-mail: jgauthier@rtdquality.com
Web Site: www.rtdquality.com


--------------------
: To the forum:

: Currently, I am testing a printed-circuit-board-mount transformer.
: There is one primary winding and three secondary windings.
: There are two powdered-iron 'E' cores that are epoxied
: together around the bobbin to provide the core for the transformer.

: I have a problem where the inductance and the Q of the primary coil
: drop way below normal past 1500 Hz with a signal of 100millivolts AC
: applied. I suspect that there is a shorted turn of wire that may be causing
: this.

: Generally, there is maybe 1000+ turns of wire on the transformer, and the
: chances of finding a marginal short-circuit with merely a microscope and
: the eyes is a 'needle-in-a-haystack' type of chance. Is there some
: method that would incorporate an electrical signal that would enable me
: to find a short-circuit in the primary winding?

: Any and all ideas are welcome. Questions are also welcome.

: Regards,

: Kelly Schauf




 
 Reply 
 

Product Spotlight

Micro CT

nanoVoxel series has nano-scale resolution upto 500nm by using high voltage X-ray source (from 80-
...
300 kV) with micro/nano focal spot and highly sensitive flat panel detectors and unique Optical coupling detector.
>

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window