where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

NOVO DR
develops and manufactures cutting edge Portable Digital Radiography X-ray Inspection Systems.
1045 views
Technical Discussions
Dent McIntyre
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 252

Dent McIntyre

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
252
09:10 Jul-12-2000
Many Holes Inspection Problem

We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.
Does not sound too tough yet does it?

The crunch is there are 16000 + holes on each plate and there are over 50 plates.

Current method is manual hole by hole with back lighting.
We have tried a video camera that actually shows the scores holes quite well but the lighting can make a bad hole look good.
We have contacted the "Vision Technical types" but they say we cannot recognize these scores with their systems.

Does anyone have any ideas?




 
 Reply 
 
Trevor Easton
Engineering
Dofasco Inc, Canada, Joined Nov 1998, 13

Trevor Easton

Engineering
Dofasco Inc,
Canada,
Joined Nov 1998
13
09:21 Jul-12-2000
Re: Many Holes Inspection Problem
: We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.

Are the scores along the full length of each hole?
A plug gauge incorporating a rotating surface measurement stylus may provide a means to recognize such a score.

You will still have to position the gauge manually unless it can be done as part of the machining process when the holes are formed.

Can you shed a little more light on the problem. Is this plate in a fixed location? What is it? Where is it?


 
 Reply 
 
Dent McIntyre
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 252

Dent McIntyre

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
252
01:44 Jul-12-2000
Re: Many Holes Inspection Problem
: : We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.

: Are the scores along the full length of each hole?

NO. The scores may start and Stop within the hole. They are caused by the broaching operation. The scores are actually on the 3 lands that are formed by the broaching process.
: A plug gauge incorporating a rotating surface measurement stylus may provide a means to recognize such a score.

: You will still have to position the gauge manually unless it can be done as part of the machining process when the holes are formed.

: Can you shed a little more light on the problem. Is this plate in a fixed location? What is it? Where is it?

The plates are all loose and are in a manufacturing shop. They are about 10' diameter




 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 280

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
280
02:35 Jul-12-2000
Re: Many Holes Inspection Problem
How unsophisticated do you want to be ?

I remember about 20 years ago having a similar problem during broaching of gearbox components. We played with surface profiling, eddy current etc.

As in the end all we wanted to do was identify good and bad we went for cheap and cheerful. Lay the plates against a solid backing pour molten wax into each hole (as is used in wax casting process) leave to cool. Push out and look for the gooving on the wax slug, mark off good versus bad holes. You can probably do a pour of 500-600 holes in30 minutes, push out and inspect one hole every 3 minutes. Wax slugs you recycle back into the melt.

Regards

John O'Brien



 
 Reply 
 
James Doyle
James Doyle
02:16 Jul-21-2000
Re: Many Holes Inspection Problem
: We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.
: Does not sound too tough yet does it?

: The crunch is there are 16000 + holes on each plate and there are over 50 plates.

: Current method is manual hole by hole with back lighting.
: We have tried a video camera that actually shows the scores holes quite well but the lighting can make a bad hole look good.
: We have contacted the "Vision Technical types" but they say we cannot recognize these scores with their systems.

: Does anyone have any ideas?

: Dent,
This may be too expensive - but we make non-contact, laser-based scanners. They can generate a profile image as well as a video-like image. We find that scratches and score marks tend to show up very well with the video image. This is not a bore scope devise.
Check out our web site www.visualogic.com

If this will be an ongoing process the probe could be positioned like a drill tool and rapidly run in-and-out of each hole.

Good luck,

Jim Doyle





 
 Reply 
 

Product Spotlight

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window