where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
3074 views
Technical Discussions
Michael Canny
NDT Inspector
Rochester Gas & Electric Corporation, USA, Joined May 2000, 1

Michael Canny

NDT Inspector
Rochester Gas & Electric Corporation,
USA,
Joined May 2000
1
09:27 Jul-14-2000
Petroleum Storage Tank - Rivet Inspection

Hello, We are the process of inspection two 1920 vintage riveted storage tanks.
Can anyone out there provide me guidelines or practices on inspecting these rivets?
Some of the rivets are conical heads (bottom half of shell) others are flat-head (top half) on these tanks.
Thanks!


 
 Reply 
 
Sam Crotchmallnick
Sam Crotchmallnick
09:47 Jul-14-2000
Re: Petroleum Storage Tank - Rivet Inspection
: Hello, We are the process of inspection two 1920 vintage riveted storage tanks.
: Can anyone out there provide me guidelines or practices on inspecting these rivets?
: Some of the rivets are conical heads (bottom half of shell) others are flat-head (top half) on these tanks.
: Thanks!

DUH! Waht color are they? What size are they? Any round heads there? What do you want? Can they be removed?




 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1300

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1300
02:24 Jul-14-2000
Re: Petroleum Storage Tank - Rivet Inspection
Michael:
I have worked on riveted boilers for old traction engines (1900-1920) to our local Canadian provincial guidelines.
There are 2 main things that might occur; the riviets may shear or the plates they are holding together may develop cracks (usually radial from the holes).
Although some people have developed conical adapted delaylines for placement over the conical rivet heads, when modelled these are shown to be of little value.
Simply grinding a flat spot large enough to put a probe on (a small probe about 6mm diameter) will allow you to get an echo off the opposite rivet head.
All you can do is try to assess if there is a crack of any significant size. This would have the arrival time shorter that the distance to the opposite rivet head of a good rivet.

Some people have used UT to look for radial cracking in the outer plate by using a UT scan around the rivet. I preferred to use fluorescent MPI (aerosol spray fluorescent particles and an AC yoke).
Either way you are usually limited to investigating the condition of the outer or exposed shell. If you have access from both sides you could do the same test both inside and outside the tanks.
Depending on the joint configuration you may have 2 or 4 layers of plate in a riveted joint. Multiple layer testing by conventional NDT is not feasible (radiography can rarely be rationalised).

ASME had requirements for "Boilers or Parts Thereof Constructed by Using Riveted Construction" in Section 1 of the 1971 edition of ASME Code. (I do not have a copy so i cannot provide details).

Hope this is a bit more informative than DUH!

Ed

: Hello, We are the process of inspection two 1920 vintage riveted storage tanks.
: Can anyone out there provide me guidelines or practices on inspecting these rivets?
: Some of the rivets are conical heads (bottom half of shell) others are flat-head (top half) on these tanks.
: Thanks!




 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 280

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
280
00:46 Jul-15-2000
Re: Petroleum Storage Tank - Rivet Inspection
Since the tanks are so old unless there is a specific reason for concern about the rivets leave well alone. Its not common to inspect individual rivets in tanks unless a problem has been determined. The rivets are constantly subjected to leak testing while the tank is in service so this would indicate a problem.

Other than this simply conduct an assessment of the tank shell as per Paragraph 2.3.4 of API 653. This provides what many would see as conservative Joint Efficiencies for assessing the shell condition of riveted tanks. This should be sufficient unless you have concerns about an additional loading factor such as wind, seismic, operations over 200 F, piping loads, settlement etc.

Corrosion thinning in the areas of the rivets is probably your biggest concern but if you do the assessment you may well find the tanks were over designed in the first place.



 
 Reply 
 
Meirion James
Meirion James
03:58 Sep-04-2000
Re: Petroleum Storage Tank - Rivet Inspection
: Hello, We are the process of inspection two 1920 vintage riveted storage tanks.
: Can anyone out there provide me guidelines or practices on inspecting these rivets?
: Some of the rivets are conical heads (bottom half of shell) others are flat-head (top half) on these tanks.
: Thanks!

We regularly inspect riveted tanks of this vintage and apart from occaisonal corrosion to the rivet heads (we sometimes use a simple cut-out profile gauge) there are rarely many problems encountered. Obvious leaking is picked up visually and can be dealt with accordingly.
I concur with the comments of John O,Brien

Meirion James


 
 Reply 
 

Product Spotlight

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Micro CT

nanoVoxel series has nano-scale resolution by using high voltage X-ray source (from 80-300 kV) wit
...
h micro focal spot and highly sensitive detector including different kinds of big size panel detectors and lens coupling CCD.
>

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window