where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

USA Borescopes
USA Borescopes is your one stop source for all your visual inspection requirements. We offer borescopes, videoscopes, push cameras and pipe ins ...
1046 views
Technical Discussions
Dent McIntyre
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 252

Dent McIntyre

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
252
09:10 Jul-12-2000
Many Holes Inspection Problem

We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.
Does not sound too tough yet does it?

The crunch is there are 16000 + holes on each plate and there are over 50 plates.

Current method is manual hole by hole with back lighting.
We have tried a video camera that actually shows the scores holes quite well but the lighting can make a bad hole look good.
We have contacted the "Vision Technical types" but they say we cannot recognize these scores with their systems.

Does anyone have any ideas?




 
 Reply 
 
Trevor Easton
Engineering
Dofasco Inc, Canada, Joined Nov 1998, 13

Trevor Easton

Engineering
Dofasco Inc,
Canada,
Joined Nov 1998
13
09:21 Jul-12-2000
Re: Many Holes Inspection Problem
: We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.

Are the scores along the full length of each hole?
A plug gauge incorporating a rotating surface measurement stylus may provide a means to recognize such a score.

You will still have to position the gauge manually unless it can be done as part of the machining process when the holes are formed.

Can you shed a little more light on the problem. Is this plate in a fixed location? What is it? Where is it?


 
 Reply 
 
Dent McIntyre
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 252

Dent McIntyre

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
252
01:44 Jul-12-2000
Re: Many Holes Inspection Problem
: : We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.

: Are the scores along the full length of each hole?

NO. The scores may start and Stop within the hole. They are caused by the broaching operation. The scores are actually on the 3 lands that are formed by the broaching process.
: A plug gauge incorporating a rotating surface measurement stylus may provide a means to recognize such a score.

: You will still have to position the gauge manually unless it can be done as part of the machining process when the holes are formed.

: Can you shed a little more light on the problem. Is this plate in a fixed location? What is it? Where is it?

The plates are all loose and are in a manufacturing shop. They are about 10' diameter




 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 280

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
280
02:35 Jul-12-2000
Re: Many Holes Inspection Problem
How unsophisticated do you want to be ?

I remember about 20 years ago having a similar problem during broaching of gearbox components. We played with surface profiling, eddy current etc.

As in the end all we wanted to do was identify good and bad we went for cheap and cheerful. Lay the plates against a solid backing pour molten wax into each hole (as is used in wax casting process) leave to cool. Push out and look for the gooving on the wax slug, mark off good versus bad holes. You can probably do a pour of 500-600 holes in30 minutes, push out and inspect one hole every 3 minutes. Wax slugs you recycle back into the melt.

Regards

John O'Brien



 
 Reply 
 
James Doyle
James Doyle
02:16 Jul-21-2000
Re: Many Holes Inspection Problem
: We need an inspection method to look fo scores inside 5/8" diameter holes. The holes are in plates about 2" thick and the scores are along the length of the hole.
: Does not sound too tough yet does it?

: The crunch is there are 16000 + holes on each plate and there are over 50 plates.

: Current method is manual hole by hole with back lighting.
: We have tried a video camera that actually shows the scores holes quite well but the lighting can make a bad hole look good.
: We have contacted the "Vision Technical types" but they say we cannot recognize these scores with their systems.

: Does anyone have any ideas?

: Dent,
This may be too expensive - but we make non-contact, laser-based scanners. They can generate a profile image as well as a video-like image. We find that scratches and score marks tend to show up very well with the video image. This is not a bore scope devise.
Check out our web site www.visualogic.com

If this will be an ongoing process the probe could be positioned like a drill tool and rapidly run in-and-out of each hole.

Good luck,

Jim Doyle





 
 Reply 
 

Product Spotlight

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window