where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1101 views
Career Discussions
ian pearson
ian pearson
08:53 Feb-05-2003
where to begin in ut

I have just enrolled in a ut level 1 course however I have no previous experience in the field,how difficult or easy will it be to pickup bearing in mind that its only 5 days!there is a weeks intro course,would that prepare me or is it a waste of time.


    
 
 Reply 
 
Timothy MacInnis
Senior NDT Engineer
SAIC/Ultra Iamge International, USA, Joined Dec 1999, 10

Timothy MacInnis

Senior NDT Engineer
SAIC/Ultra Iamge International,
USA,
Joined Dec 1999
10
09:11 Feb-05-2003
Re: where to begin in ut
Education should never be taken lightly.
There are a variety of on-line education sights that will provide you with a good intro.
This link will take you to the CNDE site. http://www.cnde.iastate.edu/.
Be advised in all educational programs you will only get out as much as you put in.



    
 
 Reply 
 
Terry White
Terry White
09:20 Feb-05-2003
Re: where to begin in ut
: I have just enrolled in a ut level 1 course however I have no previous experience in the field,how difficult or easy will it be to pickup bearing in mind that its only 5 days!there is a weeks intro course,would that prepare me or is it a waste of time.
.Relax, Ian. I did the same thing 20 years ago.Relax, Ian. I took a 5 day level 1 class in UT 20 years ago from Krautkramer and I did just fine with no prior experience. Provided that you have good instructors and training materials, you should do just fine. The level 1 course is an introductory class and you'll learn a lot. Lot's of math involved so if you're strong in that area, it's a bonus.



    
 
 Reply 
 
Neil Burleigh
Sales
Krautkramer Australia Pty Ltd, Australia, Joined Dec 2002, 158

Neil Burleigh

Sales
Krautkramer Australia Pty Ltd,
Australia,
Joined Dec 2002
158
03:46 Feb-05-2003
Re: where to begin in ut
: I have just enrolled in a ut level 1 course however I have no previous experience in the field,how difficult or easy will it be to pickup bearing in mind that its only 5 days!there is a weeks intro course,would that prepare me or is it a waste of time.
.
Ian,
We are running a Level 1 UT training course next month in Sydney Australia. If you go to the Krautkramer website there is a booklet you can download, "Non destructive Testing of Materials - Introduction to Basics" It is a 40 odd page booklet and we find it very helpful for the students.

Regards
Neil Burleigh


    
 
 Reply 
 
Dave Davies
Dave Davies
02:39 Feb-06-2003
Re: where to begin in ut
: I have just enrolled in a ut level 1 course however I have no previous experience in the field,how difficult or easy will it be to pickup bearing in mind that its only 5 days!there is a weeks intro course,would that prepare me or is it a waste of time.

Ian, Training is never wasted, but UT is a skill and nothing beats hands on experience. I started in the mid 60's and learnt most of my trade on the job. I have not stopped learning, there is always something new.
Stick at it, work on the probe, ask questions and read up on the subject. Study what you are testing as this helps greatly. Don't be afraid to ask, any operator thats worth anything will help you.
The best advice I can give is not always to believe your first impression, you are looking at a three dimensional object with a two dimensional, indirect display. If you can find a way to verify your interpretation, whether it's by using a different angle or just looking at the area in question (e.g. the reverse side of the test object, if accessible).
Stick to it, UT still gives me a buzz and there is always something to learn. Products, materials and equipment evolve and you have to evolve with them.
Good Luck and don't give up, there is great satisfaction in beating a problem.
Dave
.



    
 
 Reply 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
01:01 Feb-07-2003
Re: where to begin in ut
Ian, Good luck in your new venture (and remember, nothing ventured, nothing gained). I think that there are 3 areas where a bit of previous study prior to attendance on the course will help. If you are confident in these areas then you will be able to concentrate solely on the ultrasonic principles.

1. Very basic trigonometric functions, what i call the SOHCAHTOA memory-aid (if you dont know ask anyone reasonably proficent in maths). From this you'll be able to work out where those indications on your screen are coming from

2. Scientific notation, i.e. instead of 5000000 write 5x10 exp 6. This notation appears on most calculators and helps achieve the right answer when mixing very large and very small numbers (again ask the person in 1 above for help)

3. Manipulation of simple equations such as velocity = wavelength x frequency. You'll use this and a few other equations over the years to help select the right probe for the job.

Be confident in these 3 areas and you'll be able to concentrate fully onUT principles in that first week without struggling with fairly simple maths. And ask, ask, ask questions plus study at night so you can ask even more questions! My apologies if you are already proficient in these areas, i hope this might be of interest to others.

I'm working in the field of auto-ut (AUT) at present and there are plenty of guys working as operators with no prior ut experience so there is always an opening for you.



    
 
 Reply 
 

Product Spotlight

TOPAZ® 64: Fully Integrated Portable 32 or 64 Channel PAUT Instrument with FMC & TFM

Introducing TOPAZ64, the industry’s most intelligent fully integrated, portable 32 or 64-channel
...
phased array ultrasound (UT) instrument. TOPAZ64 combines code-compliant phased array UT with the industry’s most advanced full matrix capture (FMC) and total focusing method (TFM) capabilities. Featuring the highest acquisition frequency in its class, high resolution FMC and a 12” multi-touchscreen, users can easily visualize even the smallest flaws. TOPAZ64 can generate a bipolar pulse that provides more acoustic energy versus previous models for punching through thick components. The result is a portable tool that delivers increased inspection coverage, more accurate signals, and the ability to handle all UT inspections in one package. TOPAZ64 is ideal for challenging applications in transportation, oil and gas, manufacturing and power generation.
>

PROlineTOP Plug & Play Ultrasonic inspection device

As Plug & Play solution it units all control and operation elements in a small housing and therefo
...
re replaces the typical control cabinet...
>

CIVA 2017 UT Module

CIVA NDE Simulation Software is the world leader of NDT Simulation. The UT simulation Module incl
...
udes: - "Beam computation": Beam propagation simulation - "Inspection Simulation": Beam interaction with flaws or specimens The user can simulate a whole inspection process (pulse echo, tandem or TOFD) with a wide range of probes (conventional, Phased- arrays or EMAT), components, and flaws.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window