where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1224 views
Career Discussions
W Lee
W Lee
00:34 Sep-11-2003
Detection of cracks or pinholes on large diameter thin wall pipes

Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.


 
 Reply 
 
Richard Kazares
Richard Kazares
05:34 Sep-12-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
If you are talking about relatively short lengths of pipe - with access to the center section, we provide a system (PipeScan) that can provide a 100% wall thickness map or using shear, provide a 100% scan looking for cracks or other defects not necessarily obvious in a straight-in UT signal.

The system is automated and currently usable from 15 through 22 inches (375 - 550 mm) inside diameter - but could easily be extended up to 1 meter.

Send an e-mail and I'll send you a photo and short vidoe of the system in operation.

Hope this is helpful


----------- Start Original Message -----------
: Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
------------ End Original Message ------------




 
 Reply 
 
James Doyle
Consultant
Laser Techniques Company, LLC, USA, Joined Jan 2003, 6

James Doyle

Consultant
Laser Techniques Company, LLC,
USA,
Joined Jan 2003
6
07:31 Sep-12-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
We develop laser-based systems for similar applicaitons. They are applied from the ID however. Check our web site www.Laser-NDT.com


----------- Start Original Message -----------
: Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
------------ End Original Message ------------




 
 Reply 
 
Daniel H.Rice Consulting Services
Consultant, Ultrasonic Evaluation of Resistance Spot Welding
Daniel H. Rice Consulting Services, USA, Joined Jan 2003, 10

Daniel H.Rice Consulting Services

Consultant, Ultrasonic Evaluation of Resistance Spot Welding
Daniel H. Rice Consulting Services,
USA,
Joined Jan 2003
10
00:21 Sep-25-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
----------- Start Original Message -----------
: Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
------------ End Original Message ------------
This can be accomplished by performing the following

using Co 60 Image the pipe as you would on a elipse of a girth weld as in E94 EXCEPT the source should be perpenducular to the pipe.

Your UG should be no more than .O30 use a double load of film and .010 Pb film side intensifying screens and .010 backside intesifing screens. You may want to use a .010 intensifying screen in the middle.

use a film load of M source side and AA on the side away from the source.

Shoot a 0*,60*, and a 120* image, make sure to keep direction of flow of the pipeline consistently marked on the film.

Control your exposure to image the pipe wall use the proper IQI's.

When reading the image the image the source side will roll one way and the film side image will roll the oppisite.

"a picture is worth a 1000 Words" Ajacent to elbows will be where the corrision is the worst, as the flow accelerates and deccelerates changing direction.




 
 Reply 
 
m.trinidad
Consultant,
LMATS Pty Ltd , Australia, Joined Jan 2003, 138

m.trinidad

Consultant,
LMATS Pty Ltd ,
Australia,
Joined Jan 2003
138
07:33 Oct-04-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
There are several LRUT (Long Range UT) devices on the market which may be of some use.

The defect has got to be over a particular percentage of cross wall area to be detected which for some perculiar reason a lot of people believe LRUT cannot find pin holes. However LRUT should not be disputed out of hand as my personal experience is that yes the pit may be a pin hole on the outside but on the inside, with associated corrosion, pitting etc.

Cracking is another problem as orientation is going to be a big factor and transverse to the pipe is best. I have seen once experimentality and once in the field where cracks have been detected and both times they were rather large.

Many other factors to be considered similar to ET "many known and unknown variables" to contend with that affect the sensitivity but most likely worth you effort to get a company in to do a trial section.

Kindest Regards

Mike Trinidad
----------- Start Original Message -----------
: : Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
: This can be accomplished by performing the following
: using Co 60 Image the pipe as you would on a elipse of a girth weld as in E94 EXCEPT the source should be perpenducular to the pipe.
: Your UG should be no more than .O30 use a double load of film and .010 Pb film side intensifying screens and .010 backside intesifing screens. You may want to use a .010 intensifying screen in the middle.
: use a film load of M source side and AA on the side away from the source.
: Shoot a 0*,60*, and a 120* image, make sure to keep direction of flow of the pipeline consistently marked on the film.
: Control your exposure to image the pipe wall use the proper IQI's.
: When reading the image the image the source side will roll one way and the film side image will roll the oppisite.
: "a picture is worth a 1000 Words" Ajacent to elbows will be where the corrision is the worst, as the flow accelerates and deccelerates changing direction.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Navic - Steerable Modular Automated Scanner

The Navic is a modular, motorized, steerable scanner designed to carry multiple attachments used
...
in various scanning and inspection applications. The Navic is capable of weld scanning (girth welds and long seam welds), automated corrosion mapping, and tank scanning.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window