where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Canadian Institute for NDE
We are specialized in training for Radiography, Ultrasonics, Magnetic Particle, Liquid Penetrant, Eddy Current and emerging NDT technologies.
1338 views
Career Discussions
W Lee
W Lee
00:34 Sep-11-2003
Detection of cracks or pinholes on large diameter thin wall pipes

Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.


 
 Reply 
 
Richard Kazares
Richard Kazares
05:34 Sep-12-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
If you are talking about relatively short lengths of pipe - with access to the center section, we provide a system (PipeScan) that can provide a 100% wall thickness map or using shear, provide a 100% scan looking for cracks or other defects not necessarily obvious in a straight-in UT signal.

The system is automated and currently usable from 15 through 22 inches (375 - 550 mm) inside diameter - but could easily be extended up to 1 meter.

Send an e-mail and I'll send you a photo and short vidoe of the system in operation.

Hope this is helpful


----------- Start Original Message -----------
: Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
------------ End Original Message ------------




 
 Reply 
 
James Doyle
Consultant
Laser Techniques Company, LLC, USA, Joined Jan 2003, 6

James Doyle

Consultant
Laser Techniques Company, LLC,
USA,
Joined Jan 2003
6
07:31 Sep-12-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
We develop laser-based systems for similar applicaitons. They are applied from the ID however. Check our web site www.Laser-NDT.com


----------- Start Original Message -----------
: Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
------------ End Original Message ------------




 
 Reply 
 
Daniel H.Rice Consulting Services
Consultant, Ultrasonic Evaluation of Resistance Spot Welding
Daniel H. Rice Consulting Services, USA, Joined Jan 2003, 10

Daniel H.Rice Consulting Services

Consultant, Ultrasonic Evaluation of Resistance Spot Welding
Daniel H. Rice Consulting Services,
USA,
Joined Jan 2003
10
00:21 Sep-25-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
----------- Start Original Message -----------
: Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
------------ End Original Message ------------
This can be accomplished by performing the following

using Co 60 Image the pipe as you would on a elipse of a girth weld as in E94 EXCEPT the source should be perpenducular to the pipe.

Your UG should be no more than .O30 use a double load of film and .010 Pb film side intensifying screens and .010 backside intesifing screens. You may want to use a .010 intensifying screen in the middle.

use a film load of M source side and AA on the side away from the source.

Shoot a 0*,60*, and a 120* image, make sure to keep direction of flow of the pipeline consistently marked on the film.

Control your exposure to image the pipe wall use the proper IQI's.

When reading the image the image the source side will roll one way and the film side image will roll the oppisite.

"a picture is worth a 1000 Words" Ajacent to elbows will be where the corrision is the worst, as the flow accelerates and deccelerates changing direction.




 
 Reply 
 
m.trinidad
Consultant,
LMATS Pty Ltd , Australia, Joined Jan 2003, 141

m.trinidad

Consultant,
LMATS Pty Ltd ,
Australia,
Joined Jan 2003
141
07:33 Oct-04-2003
Re: Detection of cracks or pinholes on large diameter thin wall pipes
There are several LRUT (Long Range UT) devices on the market which may be of some use.

The defect has got to be over a particular percentage of cross wall area to be detected which for some perculiar reason a lot of people believe LRUT cannot find pin holes. However LRUT should not be disputed out of hand as my personal experience is that yes the pit may be a pin hole on the outside but on the inside, with associated corrosion, pitting etc.

Cracking is another problem as orientation is going to be a big factor and transverse to the pipe is best. I have seen once experimentality and once in the field where cracks have been detected and both times they were rather large.

Many other factors to be considered similar to ET "many known and unknown variables" to contend with that affect the sensitivity but most likely worth you effort to get a company in to do a trial section.

Kindest Regards

Mike Trinidad
----------- Start Original Message -----------
: : Can anyone let me know what types of NDT techniques/detectors are currently available for detecting cracks or pinholes on large diameter thin wall steel pipes (around 4 mm thick) for transporting liquefied natural gas? These pipes are heavily insulated.
: This can be accomplished by performing the following
: using Co 60 Image the pipe as you would on a elipse of a girth weld as in E94 EXCEPT the source should be perpenducular to the pipe.
: Your UG should be no more than .O30 use a double load of film and .010 Pb film side intensifying screens and .010 backside intesifing screens. You may want to use a .010 intensifying screen in the middle.
: use a film load of M source side and AA on the side away from the source.
: Shoot a 0*,60*, and a 120* image, make sure to keep direction of flow of the pipeline consistently marked on the film.
: Control your exposure to image the pipe wall use the proper IQI's.
: When reading the image the image the source side will roll one way and the film side image will roll the oppisite.
: "a picture is worth a 1000 Words" Ajacent to elbows will be where the corrision is the worst, as the flow accelerates and deccelerates changing direction.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

New PHAsis module for longitudinal weld seam inspection

PHAsis® Phased Array manual ultrasonic spot weld inspection device is now ideally suited for test
...
ing of longitudinally welded seams (e.g. Arplas® seam, short line seams) with a length of 3 to 12 mm.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window