where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1585 views
Career Discussions
hairul
R & D
Nuclear Institute, Malaysia, Joined Oct 2003, 1

hairul

R & D
Nuclear Institute,
Malaysia,
Joined Oct 2003
1
05:10 Nov-04-2003
looking for reliable flowmeter

I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
Regards.


    
 
 
Marius Dinu
NDT Inspector, Pre-service and In-Service Inspections
General Electric - Life Extension Services, Romania, Joined Oct 1999, 5

Marius Dinu

NDT Inspector, Pre-service and In-Service Inspections
General Electric - Life Extension Services,
Romania,
Joined Oct 1999
5
03:19 Nov-05-2003
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: Regards.
------------ End Original Message ------------

Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.

Best regards,

Marius DINU


    
 
 
Peter Vogt
Peter Vogt
06:41 Nov-10-2003
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: Regards.
------------ End Original Message ------------

Hello,

please let us know your country. After that we can pass your inquiry to the appropriate location for assistance.

Best regards


Peter Vogt


    
 
 
rodney
rodney
02:49 Nov-23-2003
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: : I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: : Regards.
: Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.
: Best regards,
: Marius DINU
------------ End Original Message ------------

endruss-hauser flowmeters are the most reliable of any flowmeter i have ever used, install very easy and adaptable to any control scheme. install them and forget about them. calibration has become a thing of the past with these babies.



    
 
 
thomas engel
thomas engel
00:52 Mar-20-2004
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: : : I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: : : Regards.
: : Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.
: : Best regards,
: : Marius DINU
: endruss-hauser flowmeters are the most reliable of any flowmeter i have ever used, install very easy and adaptable to any control scheme. install them and forget about them. calibration has become a thing of the past with these babies.
------------ End Original Message ------------

We have developed a new class of clamp on flow meters that use long wavelengths for measurement. Please see www.cidra.com sonartrac


    
 
 
Thomas Engel
Thomas Engel
00:14 Mar-25-2004
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: : : : I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: : : : Regards.
: : : Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.
: : : Best regards,
: : : Marius DINU
: : endruss-hauser flowmeters are the most reliable of any flowmeter i have ever used, install very easy and adaptable to any control scheme. install them and forget about them. calibration has become a thing of the past with these babies.
: We have developed a new class of clamp on flow meters that use long wavelengths for measurement. Please see www.cidra.com sonartrac
------------ End Original Message ------------

As a follow-up to my previous response I wouldlike to point out that our SONARtrac technology uses long wavelengths (on the order of feet) to detect flowrate. We passively listen to the vortices traveling down the pipe. Using array processing we break the signal down into its component wavelengths. Each wavelength has associated with it a particular frequency. The frequency is inversely proportional to the wavelength with the flow velocity as the proportionallity constant. Longer wavelengths cause low freqency signals, shorter wavelengths cause high frequencu signals. Averaging over the relations gives us a robust measure of the flowrate.


    
 
 
Hilfred D'Costa
Hilfred D'Costa
07:07 Nov-09-2004
Re: looking for reliable flowmeter
I may be too late but you could try EESIFLO's 11FP series which is a digital based clamp on flowmeter using advanced signal processing algorithms . We have had no problems in getting accurate measurements with this tool



    
 
 
Donald Trump
Donald Trump
09:39 Aug-19-2005
flowmeters
maybe I am too late but don't use dopplers. They are terrible for most applications except slurries and highly aerated pipes. Some manufacturers do not limit the applications of their dopplers and tell the world that they can measure anything. This is not true. We have experience with many manufacturers in the past and know which technology works well

Jonathan Jameson



    
 
 
DJ Kallhof
DJ Kallhof
06:33 Aug-24-2005
Re: flowmeters
I do not know what application you are looking for but I have had great success with Flow Technologies, Inc out of Phoenix Arizona. They're web site would be a good place to start. Check them out at www.ftimeters.com or if you prefer talking to someone give them a call at (602) 437-1315. Good luck.
----------- Start Original Message -----------
: maybe I am too late but don't use dopplers. They are terrible for most applications except slurries and highly aerated pipes. Some manufacturers do not limit the applications of their dopplers and tell the world that they can measure anything. This is not true. We have experience with many manufacturers in the past and know which technology works well
: Jonathan Jameson
------------ End Original Message ------------




    
 
 

Product Spotlight

CIVA 2017 UT Module

CIVA NDE Simulation Software is the world leader of NDT Simulation. The UT simulation Module incl
...
udes: - "Beam computation": Beam propagation simulation - "Inspection Simulation": Beam interaction with flaws or specimens The user can simulate a whole inspection process (pulse echo, tandem or TOFD) with a wide range of probes (conventional, Phased- arrays or EMAT), components, and flaws.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window