where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

900 views
Career Discussions
Jens Forker
Jens Forker
08:27 Jun-25-2004
low frequency UT probe

Dear all,
Who can help or knows a possible source?

We are looking for a UT probe with almost linear efficiency (if excited by a continuous sine wave) in the band width from (roughly) 10kHz up to 200kHz (we want to sweep the frequency across this range).
Also probes from around 10-100kHz and from 50-200kHz might be of interest.
We need a flat coupling area to couple this probe to solids.

thanks and regards
Jens


 
 Reply 
 
N.Kuppusamy
Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd, Singapore, Joined Dec 2003, 34

N.Kuppusamy

Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd,
Singapore,
Joined Dec 2003
34
04:03 Jun-26-2004
Re: low frequency UT probe
Hi,
You can contact probe manufacturers such as Krautkramer with your specific requirement. They will construct and supply to you.
N.Kuppusamy

----------- Start Original Message -----------
: Dear all,
: Who can help or knows a possible source?
: We are looking for a UT probe with almost linear efficiency (if excited by a continuous sine wave) in the band width from (roughly) 10kHz up to 200kHz (we want to sweep the frequency across this range).
: Also probes from around 10-100kHz and from 50-200kHz might be of interest.
: We need a flat coupling area to couple this probe to solids.
: thanks and regards
: Jens
------------ End Original Message ------------




 
 Reply 
 
Simon Amallraja
Simon Amallraja
07:01 Jun-30-2004
Re: low frequency UT probe
----------- Start Original Message -----------
: Dear all,
: Who can help or knows a possible source?
: We are looking for a UT probe with almost linear efficiency (if excited by a continuous sine wave) in the band width from (roughly) 10kHz up to 200kHz (we want to sweep the frequency across this range).
: Also probes from around 10-100kHz and from 50-200kHz might be of interest.
: We need a flat coupling area to couple this probe to solids.
: thanks and regards
: Jens
------------ End Original Message ------------

Dear jens,

Please contact us with more specific data to give u the quote.

Regards.

Simon Amallraja.


 
 Reply 
 
J. Dong
J. Dong
02:23 Jul-01-2004
Re: low frequency UT probe
Hi,

Physical Acoustics Corporation's S9208 sensor is pretty good for this application. It has flat response in this frequency bandwidth. I have used it as an excitation sensor for years.


----------- Start Original Message -----------
: Dear all,
: Who can help or knows a possible source?
: We are looking for a UT probe with almost linear efficiency (if excited by a continuous sine wave) in the band width from (roughly) 10kHz up to 200kHz (we want to sweep the frequency across this range).
: Also probes from around 10-100kHz and from 50-200kHz might be of interest.
: We need a flat coupling area to couple this probe to solids.
: thanks and regards
: Jens
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Echomac® PA Bar Tester

The Echomac® PA BT provides 100% inspection of round bars for core and surface defects, at speeds u
...
p to 2 m/sec, depending on the specific application. The unit allows producers to handle a much larger range of diameters in one installation, and is available in 3 models to test 10 – 75mm diameter (small model); 20 – 130mm (medium model) or 50 – 254mm (large model) bars.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window