where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ULTRASOUND INSTITUTE
The Ultrasound Institute can develop new advanced ultrasonic measurement, imaging and NDT techniques for non-conventional applications.
481 views
Career Discussions
Junjira
Junjira
02:33 Aug-17-2004
Job's Qualification of 3rd Inspector

I am searching for the Inspector 's qualification to be performed the 3rd inspction for OCTG-Tubular, W/H&XT and downhole equiupment.
Could you help to provide any infomation for me??
Thanks and Best regards,
JT



 
 Reply 
 
Nat
Engineering, Chief Examiner -NDT Manager
SGS EGYPT, Singapore, Joined Jan 2002, 4

Nat

Engineering, Chief Examiner -NDT Manager
SGS EGYPT,
Singapore,
Joined Jan 2002
4
04:53 Aug-17-2004
Re: Job's Qualification of 3rd Inspector
----------- Start Original Message -----------
: I am searching for the Inspector 's qualification to be performed the 3rd inspction for OCTG-Tubular, W/H&XT and downhole equiupment.
: Could you help to provide any infomation for me??
: Thanks and Best regards,
: JT
------------ End Original Message ------------
API standard states that Inspection personnel shall be qualified and certified as per the written practice of the company , Most of the companies are following ASNT ‘s Recommended practice ,SNT-TC-1A to qualify and certify their inspection personnel.

Certifications from Organization like IPIA( international pipe inspectors association ) and T.H Hill are also recognized.

The third party inspector should be ideally should have at least Level II in UT, MT,PT,VT and ET Experience and certifications obtained in OCTG sector




 
 Reply 
 

Product Spotlight

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window