where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ACS-Solutions GmbH
develop and manufacture hi-tech devices for Ultrasonic Testing
895 views
Technical Discussions
Gharieb Adly Ali
Other, Ultrasonic Researcher
National Institute for Standards, Egypt, Joined Oct 1999, 1

Gharieb Adly Ali

Other, Ultrasonic Researcher
National Institute for Standards,
Egypt,
Joined Oct 1999
1
05:04 Sep-18-2000
Elect.Impedance of PZT Pickup


Dear colleagues

For economical purpose I had construct a simple PZT pickup
From PZT -4 Material of Fundamental frequency 2MHZ
When I measured the Electrical Impedance of Pickup against frequency
(Over frequency range 10 KHz to 4 MHZ )
I was found three Peaks
1- first at 250 kHz
2- second at 850 kHz
3- third at 3300 kHz
I Haven't explanation for this result, may be any colleague
has an explanation
Thank you very much



    
 
 Reply 
 
Jim Barshinger
Engineering
General Electric Global Research Center, USA, Joined Aug 2000, 8

Jim Barshinger

Engineering
General Electric Global Research Center,
USA,
Joined Aug 2000
8
05:44 Sep-18-2000
Re: Elect.Impedance of PZT Pickup
:
: Dear colleagues

: For economical purpose I had construct a simple PZT pickup
: From PZT -4 Material of Fundamental frequency 2MHZ
: When I measured the Electrical Impedance of Pickup against frequency
: (Over frequency range 10 KHz to 4 MHZ )
: I was found three Peaks
: 1- first at 250 kHz
: 2- second at 850 kHz
: 3- third at 3300 kHz
: I Haven't explanation for this result, may be any colleague
: has an explanation
: Thank you very much

The first and second peaks are most likely lateral resonances in the material. If you only have one lateral dimension, for instance a circular or square ceramic, I would guess that the 250 kHz peak is the fundamental lateral resonance and the 850 kHz peak is the third harmonic of the lateral resonance. The 3300 kHz peak should be your fundamental thickness mode resonance. I'm guessing that you are measuring the parallel resonance which will be a point of maximum real impedance. The series resonance should occur slightly lower in frequency and is a point of minimum real impedance. This should occur at 2 MHz (if you have ground your ceramic to the correct thickness). The center frequency that the device will run at depends on whether your recieving electronics matches better with the series or parallel resonance.

Good luck,
Jim





    
 
 Reply 
 

Product Spotlight

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

Silverwing RMS PA - Phased-array corrosion mapping

Eddyfi Technologies integrated two market leading solutions, Silverwing’s RMS and M2M’s instru
...
ments to provide a high-speed, remote access ultrasonic phased-array inspection system with live total focusing method (TFM).
>

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window