where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

NOVO DR
develops and manufactures cutting edge Portable Digital Radiography X-ray Inspection Systems.
1667 views
Career Discussions
hairul
R & D
Nuclear Institute, Malaysia, Joined Oct 2003, 1

hairul

R & D
Nuclear Institute,
Malaysia,
Joined Oct 2003
1
05:10 Nov-04-2003
looking for reliable flowmeter

I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
Regards.


 
 Reply 
 
Marius Dinu
NDT Inspector, Pre-service and In-Service Inspections
General Electric - Life Extension Services, Romania, Joined Oct 1999, 5

Marius Dinu

NDT Inspector, Pre-service and In-Service Inspections
General Electric - Life Extension Services,
Romania,
Joined Oct 1999
5
03:19 Nov-05-2003
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: Regards.
------------ End Original Message ------------

Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.

Best regards,

Marius DINU


 
 Reply 
 
Peter Vogt
Peter Vogt
06:41 Nov-10-2003
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: Regards.
------------ End Original Message ------------

Hello,

please let us know your country. After that we can pass your inquiry to the appropriate location for assistance.

Best regards


Peter Vogt


 
 Reply 
 
rodney
rodney
02:49 Nov-23-2003
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: : I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: : Regards.
: Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.
: Best regards,
: Marius DINU
------------ End Original Message ------------

endruss-hauser flowmeters are the most reliable of any flowmeter i have ever used, install very easy and adaptable to any control scheme. install them and forget about them. calibration has become a thing of the past with these babies.



 
 Reply 
 
thomas engel
thomas engel
00:52 Mar-20-2004
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: : : I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: : : Regards.
: : Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.
: : Best regards,
: : Marius DINU
: endruss-hauser flowmeters are the most reliable of any flowmeter i have ever used, install very easy and adaptable to any control scheme. install them and forget about them. calibration has become a thing of the past with these babies.
------------ End Original Message ------------

We have developed a new class of clamp on flow meters that use long wavelengths for measurement. Please see www.cidra.com sonartrac


 
 Reply 
 
Thomas Engel
Thomas Engel
00:14 Mar-25-2004
Re: looking for reliable flowmeter
----------- Start Original Message -----------
: : : : I'm looking for a reliable flowmeter for measuring liquid, water and oil inside a pipeline. Currently, I'm using Doppler Flowmeter from Dynamic Fluid Systems. I woud appreciate if someone can advise on this.
: : : : Regards.
: : : Look after Controlotron Corporation (www.controlotron.com) in NY, USA. They have a lot of ultrasonic flowmeters (both transit time method and Doppler effect) that can be suitable for your application.
: : : Best regards,
: : : Marius DINU
: : endruss-hauser flowmeters are the most reliable of any flowmeter i have ever used, install very easy and adaptable to any control scheme. install them and forget about them. calibration has become a thing of the past with these babies.
: We have developed a new class of clamp on flow meters that use long wavelengths for measurement. Please see www.cidra.com sonartrac
------------ End Original Message ------------

As a follow-up to my previous response I wouldlike to point out that our SONARtrac technology uses long wavelengths (on the order of feet) to detect flowrate. We passively listen to the vortices traveling down the pipe. Using array processing we break the signal down into its component wavelengths. Each wavelength has associated with it a particular frequency. The frequency is inversely proportional to the wavelength with the flow velocity as the proportionallity constant. Longer wavelengths cause low freqency signals, shorter wavelengths cause high frequencu signals. Averaging over the relations gives us a robust measure of the flowrate.


 
 Reply 
 
Hilfred D'Costa
Hilfred D'Costa
07:07 Nov-09-2004
Re: looking for reliable flowmeter
I may be too late but you could try EESIFLO's 11FP series which is a digital based clamp on flowmeter using advanced signal processing algorithms . We have had no problems in getting accurate measurements with this tool



 
 Reply 
 
Donald Trump
Donald Trump
09:39 Aug-19-2005
flowmeters
maybe I am too late but don't use dopplers. They are terrible for most applications except slurries and highly aerated pipes. Some manufacturers do not limit the applications of their dopplers and tell the world that they can measure anything. This is not true. We have experience with many manufacturers in the past and know which technology works well

Jonathan Jameson



 
 Reply 
 
DJ Kallhof
DJ Kallhof
06:33 Aug-24-2005
Re: flowmeters
I do not know what application you are looking for but I have had great success with Flow Technologies, Inc out of Phoenix Arizona. They're web site would be a good place to start. Check them out at www.ftimeters.com or if you prefer talking to someone give them a call at (602) 437-1315. Good luck.
----------- Start Original Message -----------
: maybe I am too late but don't use dopplers. They are terrible for most applications except slurries and highly aerated pipes. Some manufacturers do not limit the applications of their dopplers and tell the world that they can measure anything. This is not true. We have experience with many manufacturers in the past and know which technology works well
: Jonathan Jameson
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Wireless TOFD scanner

Quick, accurate and highly reproducible welds testing. The System operates wirelessly and is compat
...
ible with any type of Windows based Laptop, Desktop or Tablet.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window