where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

2235 views
Career Discussions
john bisceglia
john bisceglia
06:27 Apr-04-2006
microdot bnc connectors

I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections


 
 Reply 
 
Linas Svilainis
R & D,
Kaunas University of Technology, Lithuania, Joined Nov 1998, 68

Linas Svilainis

R & D,
Kaunas University of Technology,
Lithuania,
Joined Nov 1998
68
04:16 Apr-05-2006
Re: microdot bnc connectors
----------- Start Original Message -----------
: I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections
------------ End Original Message ------------

Up to my knowledge microdot can be assembled without crimping (refer to AMP instruction sheet 408-8521 former RF-ASMB-88). I used manual pressfitting using a simpte screw.
The other brand I know is KY-017 KY-018. I only have a pictures - I think the RG174 cable shloud be used here. So, RG174 crimp tool should do.




 
 Reply 
 
Rob with(tuboscope)
Rob with(tuboscope)
05:48 Apr-13-2007
Re: microdot bnc connectors
----------- Start Original Message -----------
: : I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections
: Up to my knowledge microdot can be assembled without crimping (refer to AMP instruction sheet 408-8521 former RF-ASMB-88). I used manual pressfitting using a simpte screw.
: The other brand I know is KY-017 KY-018. I only have a pictures - I think the RG174 cable shloud be used here. So, RG174 crimp tool should do.
------------ End Original Message ------------

http://www.usultratek.com/products/connectors.htm



 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 528

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
528
02:40 Apr-13-2007
Re: microdot bnc connectors

It depends what you are using them for, If its a static connection then its not too critical. If the connector is being flexed a lot (as it would if you have it on a UT Probe) then optimal crimping /strain relief makes a lot of difference to how long the assembly lasts. (using the wrong tool can greatly reduce the connection strength) I presume you want to make your own cables up to save costs, If you are replacing them more often that may prove a false economy.

You might want to look at the compatible connectors from Microtech

http://www.mmm-microtech.com/BSeries.htm

They aren't quite as robust as the full military spec microdots, but they are (or used to be, its been a while) a lot cheaper and easier to use.

Joe


----------- Start Original Message -----------
: : : I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections
: : Up to my knowledge microdot can be assembled without crimping (refer to AMP instruction sheet 408-8521 former RF-ASMB-88). I used manual pressfitting using a simpte screw.
: : The other brand I know is KY-017 KY-018. I only have a pictures - I think the RG174 cable shloud be used here. So, RG174 crimp tool should do.
: http://www.usultratek.com/products/connectors.htm
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Magnetic X-Ray Pipeline Crawler 6''-60''

Suitable to work in 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometer
...
s and provide the efficient inspection of the pipeline.
>

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window