where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
491 views
Technical Discussions
Dave Wilkes
Dave Wilkes
08:55 Oct-28-2000
Data acquisition & USN52R

Data acquisition & USN52R

How can I do the data acquisition from the USN52R, this equipment has an auxiliary port but the output is in DC values, I need to get and RF signal for post-processing whit DSP tools.

"This message was posted on behalf of Roberto Henry who does not have internet access, but has an email address. Therefore could anyone answering this question also email Roberto a copy at henry@aconci.perla.inf.cu "




 
 Reply 
 
Wolfgang.Bisle
Wolfgang.Bisle
01:57 Nov-06-2000
Re: Data acquisition & USN52R
Do it by reading out the instrument digitally via RS232 - it is the only standard way. But I guess it is much too slow for a DSP.
Why don't you use a PC-Card based system for such an application. Then you can get access to the raw data as quick as possible. The USN52 is really the wrong instrument for this.
For a good performance you may use a standard PC digitizer slotcard with sufficient speed and dynamic (SONIXS, Signatec, GAGE, Spectrum, ACQIRIS). These cards often might be directly interfaced to a DSP.
And look for a good pulser/receiver board - that's all you need for optimum signal processing. If the receiver das DAC capabilities, don't forget to take this into account into your DSP routines.



 
 Reply 
 
Richard Kazares
Richard Kazares
02:40 Nov-07-2000
Re: Data acquisition & USN52R
A new additiuon to our Digital Signal Processing product line is the newly introduced, 12 bit A/D board manufactured by Physical Acoustics Corporation. This 100 MSamples/second board interfaces (piggy-back using 1 PCI slot only) with an available 300/400 V. Pulser/Receiver board.

Contact Physical Acoustics Corporation for more information. www.pacndt.com


: Data acquisition & USN52R
:
: How can I do the data acquisition from the USN52R, this equipment has an auxiliary port but the output is in DC values, I need to get and RF signal for post-processing whit DSP tools.

: "This message was posted on behalf of Roberto Henry who does not have internet access, but has an email address. Therefore could anyone answering this question also email Roberto a copy at henry@aconci.perla.inf.cu "




 
 Reply 
 
liheping
liheping
06:02 Jan-11-2001
Re: Data acquisition & USN52R
: Do it by reading out the instrument digitally via RS232 - it is the only standard way. But I guess it is much too slow for a DSP.
: Why don't you use a PC-Card based system for such an application. Then you can get access to the raw data as quick as possible. The USN52 is really the wrong instrument for this.
: For a good performance you may use a standard PC digitizer slotcard with sufficient speed and dynamic (SONIXS, Signatec, GAGE, Spectrum, ACQIRIS). These cards often might be directly interfaced to a DSP.
: And look for a good pulser/receiver board - that's all you need for optimum signal processing. If the receiver das DAC capabilities, don't forget to take this into account into your DSP routines.




 
 Reply 
 
Sasha Grebenyuk
Sasha Grebenyuk
02:04 Dec-07-2001
Undocumented commands of USN 52!
Hello!
Can anybody tell me something about undocumented commands of USN 52 (M4): DA, JD, JW, YP, YY?

Best regards...
Sasha Grebenyuk


 
 Reply 
 

Product Spotlight

NovaScope 6000

The all-digital Novascope 6000 is a portable, ultra-high precision thickness gauge for high-speed
...
thickness measurement. Novascope 6000 has unmatched capabilities and unique features including: •Superior Resolution with high contrast, high-speed color RF display •High pulser voltage •Real-time video output •Increased internal/external data storage •Programmable SetUp features •Battery & AC Powered
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window