where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
487 views
Technical Discussions
Dave Wilkes
Dave Wilkes
08:55 Oct-28-2000
Data acquisition & USN52R

Data acquisition & USN52R

How can I do the data acquisition from the USN52R, this equipment has an auxiliary port but the output is in DC values, I need to get and RF signal for post-processing whit DSP tools.

"This message was posted on behalf of Roberto Henry who does not have internet access, but has an email address. Therefore could anyone answering this question also email Roberto a copy at henry@aconci.perla.inf.cu "




 
 Reply 
 
Wolfgang.Bisle
Wolfgang.Bisle
01:57 Nov-06-2000
Re: Data acquisition & USN52R
Do it by reading out the instrument digitally via RS232 - it is the only standard way. But I guess it is much too slow for a DSP.
Why don't you use a PC-Card based system for such an application. Then you can get access to the raw data as quick as possible. The USN52 is really the wrong instrument for this.
For a good performance you may use a standard PC digitizer slotcard with sufficient speed and dynamic (SONIXS, Signatec, GAGE, Spectrum, ACQIRIS). These cards often might be directly interfaced to a DSP.
And look for a good pulser/receiver board - that's all you need for optimum signal processing. If the receiver das DAC capabilities, don't forget to take this into account into your DSP routines.



 
 Reply 
 
Richard Kazares
Richard Kazares
02:40 Nov-07-2000
Re: Data acquisition & USN52R
A new additiuon to our Digital Signal Processing product line is the newly introduced, 12 bit A/D board manufactured by Physical Acoustics Corporation. This 100 MSamples/second board interfaces (piggy-back using 1 PCI slot only) with an available 300/400 V. Pulser/Receiver board.

Contact Physical Acoustics Corporation for more information. www.pacndt.com


: Data acquisition & USN52R
:
: How can I do the data acquisition from the USN52R, this equipment has an auxiliary port but the output is in DC values, I need to get and RF signal for post-processing whit DSP tools.

: "This message was posted on behalf of Roberto Henry who does not have internet access, but has an email address. Therefore could anyone answering this question also email Roberto a copy at henry@aconci.perla.inf.cu "




 
 Reply 
 
liheping
liheping
06:02 Jan-11-2001
Re: Data acquisition & USN52R
: Do it by reading out the instrument digitally via RS232 - it is the only standard way. But I guess it is much too slow for a DSP.
: Why don't you use a PC-Card based system for such an application. Then you can get access to the raw data as quick as possible. The USN52 is really the wrong instrument for this.
: For a good performance you may use a standard PC digitizer slotcard with sufficient speed and dynamic (SONIXS, Signatec, GAGE, Spectrum, ACQIRIS). These cards often might be directly interfaced to a DSP.
: And look for a good pulser/receiver board - that's all you need for optimum signal processing. If the receiver das DAC capabilities, don't forget to take this into account into your DSP routines.




 
 Reply 
 
Sasha Grebenyuk
Sasha Grebenyuk
02:04 Dec-07-2001
Undocumented commands of USN 52!
Hello!
Can anybody tell me something about undocumented commands of USN 52 (M4): DA, JD, JW, YP, YY?

Best regards...
Sasha Grebenyuk


 
 Reply 
 

Product Spotlight

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

Teletest Focus+

Teletest Focus+ electronics have superior capabilities than rivals on the market. Beyond the usual
...
test features, Focus+ has 24 transmit channels and 24 receive channels, with an additional on-board switching capabilities. The instrument's frequency range is 10–300 kHz.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window