where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1151 views
Technical Discussions
Dr.Rajendran
R & D
MEPCO SCHLENK ENGINEERING COLLEGE, India, Joined Nov 2000, 3

Dr.Rajendran

R & D
MEPCO SCHLENK ENGINEERING COLLEGE,
India,
Joined Nov 2000
3
05:57 Nov-06-2000
high temperature ultrasonics materials characterisation


Dear Colleagues,

I would like to know the details of the high temperature experimental setup for ultrasonics materials characterisation.


 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
06:23 Nov-06-2000
Re: high temperature ultrasonics materials characterisation
:
: Dear Colleagues,

: I would like to know the details of the high temperature experimental setup for ultrasonics materials characterisation.

What is the temperature range over which you wish to work, what types of material are you testing, and what properties do you wish to examine? The answers to those questions will determine what equipment and techniques are appropriate.

You can find a basic introduction to ultrasonic material analysis on the Panametrics web site at:
www.panametrics.com/div_ndt/pages/theory/material.shtml

--Tom Nelligan




 
 Reply 
 
M. Kim Johnson
M. Kim Johnson
01:01 Nov-06-2000
Re: high temperature ultrasonics materials characterisation
: :
: : Dear Colleagues,

: : I would like to know the details of the high temperature experimental setup for ultrasonics materials characterisation.

You may wish to consider Resonant Ultrasound Spectroscopy for this application. It has been used succesfully for material characterization up to about 1800° C, although the accuracy decreases as the temperature increases. Please check the web site (http://www.quasarintl.com/ruspec/ruspec.html. We do not build high temperature fixtures, but can provide a description of how to do so or put you in tough with someone who gas built one.

M. Kim Johnson


 
 Reply 
 
Marvin Klein
Marvin Klein
03:40 Nov-07-2000
Re: high temperature ultrasonics materials characterisation
:
: Dear Colleagues,

: I would like to know the details of the high temperature experimental setup for ultrasonics materials characterisation.

If you are working at very high temperatures, laser ultrasonics allows characterization without contacting the sample. One good reference is "Laser Ultrasonics" by C. Scruby and L. Drain. You will also find some useful information on the Lasson web site (www.lasson.com).

Marvin Klein



 
 Reply 
 
Jan Verkooijen
Director,
Sonovation, Netherlands, Joined Nov 1998, 29

Jan Verkooijen

Director,
Sonovation,
Netherlands,
Joined Nov 1998
29
00:52 Nov-07-2000
Re: high temperature ultrasonics materials characterisation
You might be interested to know, that we have just completed a program of work
for detection and sizing of defects in welds at high temperature.
The highest temperature at which we performed an inspection was 400 degrees C
during the actual sitework. The process was fully validated on forehand up
to temperatures of 450 degrees C.
Thicknesses of the material varied from some 100 mm carbon steel to around 220 mm
in various configurations.

We will be placing some results on our website (www.sonovation.com) shortly.

Jan Verkooijen

:
: Dear Colleagues,

: I would like to know the details of the high temperature experimental setup for ultrasonics materials characterisation.




 
 Reply 
 
Dr.V.RAJENDRAN
R & D
MEPCO SCHLENK ENGINEERING COLLEGE, India, Joined Nov 2000, 3

Dr.V.RAJENDRAN

R & D
MEPCO SCHLENK ENGINEERING COLLEGE,
India,
Joined Nov 2000
3
01:25 Nov-07-2000
Re: high temperature ultrasonics materials characterisation
: You might be interested to know, that we have just completed a program of work
: for detection and sizing of defects in welds at high temperature.
: The highest temperature at which we performed an inspection was 400 degrees C
: during the actual sitework. The process was fully validated on forehand up
: to temperatures of 450 degrees C.
: Thicknesses of the material varied from some 100 mm carbon steel to around 220 mm
: in various configurations.

: We will be placing some results on our website (www.sonovation.com) shortly.

: Jan Verkooijen

: :
: : Dear Colleagues,

: : I would like to know the details of the high temperature experimental setup for ultrasonics materials characterisation.




 
 Reply 
 
Dr. V. RAJENDRAN
R & D
MEPCO SCHLENK ENGINEERING COLLEGE, India, Joined Nov 2000, 3

Dr. V. RAJENDRAN

R & D
MEPCO SCHLENK ENGINEERING COLLEGE,
India,
Joined Nov 2000
3
01:27 Nov-07-2000
Re: high temperature ultrasonics materials characterisation
: :
: : Dear Colleagues,

: : I would like to know the details of the high temperature experimental setup for ultrasonics materials characterisation.

: If you are working at very high temperatures, laser ultrasonics allows characterization without contacting the sample. One good reference is "Laser Ultrasonics" by C. Scruby and L. Drain. You will also find some useful information on the Lasson web site (www.lasson.com).

: Marvin Klein




 
 Reply 
 

Product Spotlight

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

Research and Applications Development For NDT

The Research and Applications Development (RAD) group is a newly formed team within Acuren dedicat
...
ed to tackling challenging inspection problems. Our focus is the development of novel, field deployable, advanced inspection techniques for use in cases where standard NDT methods are ineffective. We don't wait for new innovations, we engineer them. From concept to commissioning.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Aerospace Systems - Automated Ultrasonic Inspection

USL are specialists in the design and manufacture of turnkey ultrasonic inspection systems for aer
...
ospace applications. From monolithic composites to complex honeycomb structures. This video shows just a few examples of what is possible, find out more at: www.ultrasonic-sciences.co.uk
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window