where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
490 views
Technical Discussions
Dave Wilkes
Dave Wilkes
08:55 Oct-28-2000
Data acquisition & USN52R

Data acquisition & USN52R

How can I do the data acquisition from the USN52R, this equipment has an auxiliary port but the output is in DC values, I need to get and RF signal for post-processing whit DSP tools.

"This message was posted on behalf of Roberto Henry who does not have internet access, but has an email address. Therefore could anyone answering this question also email Roberto a copy at henry@aconci.perla.inf.cu "




 
 Reply 
 
Wolfgang.Bisle
Wolfgang.Bisle
01:57 Nov-06-2000
Re: Data acquisition & USN52R
Do it by reading out the instrument digitally via RS232 - it is the only standard way. But I guess it is much too slow for a DSP.
Why don't you use a PC-Card based system for such an application. Then you can get access to the raw data as quick as possible. The USN52 is really the wrong instrument for this.
For a good performance you may use a standard PC digitizer slotcard with sufficient speed and dynamic (SONIXS, Signatec, GAGE, Spectrum, ACQIRIS). These cards often might be directly interfaced to a DSP.
And look for a good pulser/receiver board - that's all you need for optimum signal processing. If the receiver das DAC capabilities, don't forget to take this into account into your DSP routines.



 
 Reply 
 
Richard Kazares
Richard Kazares
02:40 Nov-07-2000
Re: Data acquisition & USN52R
A new additiuon to our Digital Signal Processing product line is the newly introduced, 12 bit A/D board manufactured by Physical Acoustics Corporation. This 100 MSamples/second board interfaces (piggy-back using 1 PCI slot only) with an available 300/400 V. Pulser/Receiver board.

Contact Physical Acoustics Corporation for more information. www.pacndt.com


: Data acquisition & USN52R
:
: How can I do the data acquisition from the USN52R, this equipment has an auxiliary port but the output is in DC values, I need to get and RF signal for post-processing whit DSP tools.

: "This message was posted on behalf of Roberto Henry who does not have internet access, but has an email address. Therefore could anyone answering this question also email Roberto a copy at henry@aconci.perla.inf.cu "




 
 Reply 
 
liheping
liheping
06:02 Jan-11-2001
Re: Data acquisition & USN52R
: Do it by reading out the instrument digitally via RS232 - it is the only standard way. But I guess it is much too slow for a DSP.
: Why don't you use a PC-Card based system for such an application. Then you can get access to the raw data as quick as possible. The USN52 is really the wrong instrument for this.
: For a good performance you may use a standard PC digitizer slotcard with sufficient speed and dynamic (SONIXS, Signatec, GAGE, Spectrum, ACQIRIS). These cards often might be directly interfaced to a DSP.
: And look for a good pulser/receiver board - that's all you need for optimum signal processing. If the receiver das DAC capabilities, don't forget to take this into account into your DSP routines.




 
 Reply 
 
Sasha Grebenyuk
Sasha Grebenyuk
02:04 Dec-07-2001
Undocumented commands of USN 52!
Hello!
Can anybody tell me something about undocumented commands of USN 52 (M4): DA, JD, JW, YP, YY?

Best regards...
Sasha Grebenyuk


 
 Reply 
 

Product Spotlight

Teletest Focus+

Teletest Focus+ electronics have superior capabilities than rivals on the market. Beyond the usual
...
test features, Focus+ has 24 transmit channels and 24 receive channels, with an additional on-board switching capabilities. The instrument's frequency range is 10–300 kHz.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window