where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ULTRASOUND INSTITUTE
The Ultrasound Institute can develop new advanced ultrasonic measurement, imaging and NDT techniques for non-conventional applications.
1580 views
Technical Discussions
Christine Olive
Christine Olive
01:16 Jan-29-2001
Re: Radiography of Tubes with Source on Tubes



 
 Reply 
 
Alan Beveridge
Alan Beveridge
04:43 Dec-13-2000
Radiography of Tubes with Source on Tubes

Does anyone have any information on a radiographic technique in which the source is placed onto the tube surface. Types of tubes are 2" OD, I believe the technique uses an Iridium source with a strength of 5 curies or less.

Any info on sensitivity, or who uses such a technique?

Regards,

Alan Beveridge


 
 Reply 
 
Dent McIntyre
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 248

Dent McIntyre

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
248
03:39 Dec-13-2000
Re: Radiography of Tubes with Source on Tubes
Alan:
Some years ago we used this technique on a nuclear piping job. The tiny Ir 192 source was so small we could actually perform panoramic shots and still meet Ug requirements. 2-2T was no problem.
How thick is the wall of these tubes?

Dent McIntyre
NDE Manager
B & W Canada

: Does anyone have any information on a radiographic technique in which the source is placed onto the tube surface. Types of tubes are 2" OD, I believe the technique uses an Iridium source with a strength of 5 curies or less.

: Any info on sensitivity, or who uses such a technique?

: Regards,

: Alan Beveridge




 
 Reply 
 
Robert A. Day
Engineering
Milky Way Jewels, USA, Joined Nov 1998, 40

Robert A. Day

Engineering
Milky Way Jewels,
USA,
Joined Nov 1998
40
01:49 Dec-13-2000
Re: Radiography of Tubes with Source on Tubes



 
 Reply 
 
Alan Beveridge
Alan Beveridge
06:53 Dec-14-2000
Re: Thickness ofTubes for Dent McIntyre
: Dent,

Tube thicknesses vary from 3.4mm in reheater to 9.5mm in the final stage superheater.

Our local NDT companies have source sizes of 2mmx2mm, and 3mmx3mm Iridium.

Regards,

Alan Beveridge





 
 Reply 
 
Dent McIntyre
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 248

Dent McIntyre

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
248
04:49 Dec-14-2000
Re: Thickness ofTubes for Dent McIntyre



 
 Reply 
 
Alan Beveridge
Alan Beveridge
05:25 Dec-15-2000
Re: Radiography of Tubes with Source on Tubes
: Dent,

Tube thickness varies from 3.4mm in our reheater to 9.5mm in the final stage superheater.

Regards,

Alan Beveridge

Alan:
: Some years ago we used this technique on a nuclear piping job. The tiny Ir 192 source was so small we could actually perform panoramic shots and still meet Ug requirements. 2-2T was no problem.
: How thick is the wall of these tubes?

: Dent McIntyre
: NDE Manager
: B & W Canada




 
 Reply 
 
BobC
BobC
03:52 Dec-20-2000
Re: Radiography of Tubes with Source on Tubes
I regards to your question, you must first determine to which code, or to what specification you are to be in compliance with. ASME generaly requires anything below 3.5" od to be radiographed using a superimposed or eliptical technique. On the other end of the spectrum Gas piping code has essentially the same requirement. Most codes make provision for the engineer to approve alternate techniques, but in general you are going to want the smallest physical source that you can get. Hope some of this helps.



 
 Reply 
 
Farshad Mobasher-Fard
Engineering
Nikan Machine, Iran, Joined Sep 2001, 3

Farshad Mobasher-Fard

Engineering
Nikan Machine,
Iran,
Joined Sep 2001
3
07:54 Sep-18-2001
Re: Radiography of Tubes with Source on Tubes
Re: Radiography of Tubes with Source on Tubes


 
 Reply 
 

Product Spotlight

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

Navic - Steerable Modular Automated Scanner

The Navic is a modular, motorized, steerable scanner designed to carry multiple attachments used
...
in various scanning and inspection applications. The Navic is capable of weld scanning (girth welds and long seam welds), automated corrosion mapping, and tank scanning.
>

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window