where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
996 views
Technical Discussions
M. W. Moyer
M. W. Moyer
06:34 Feb-19-2001
Radial Surface Waves

Does anyone have some references about using radial surface waves
from short focused transducers to detect surface and near surface
defects and material property variations?
Thanks in advance for your help.

M. W. Moyer


 
 Reply 
 
Albrecht Maurer
Albrecht Maurer
08:48 Feb-20-2001
Re: Radial Surface Waves
: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.
Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.


 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 608

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
608
00:47 Feb-20-2001
Re: Radial Surface Waves
Mr Gripp's paper is available at:
Surface Crack Detection Using Rayleigh Waves - in immersion: A Novel Application of a Known Principle
http://www.ndt.net/article/wcndt00/papers/idn031/idn031.htm

Also I would like to take the opportunity to introduce a problem of the email address used in the forum message.
Albrecht Maurer used in his message the email address "albrecht_maurer@nukem.de",
but his Member Profile is registers with the email address "Nutronik@Nukem.de".
The system can set Profile and Exhibitors links only according to the registered Forum Profiles.

Mr. Maurer's Profile: http://www.ndt.net/wshop/profile/profiles/123.htm
NUKEM Nutronik GmbH: http://www.ndt.net/exhibit/stand/15_ky.htm

That means you shall use for forum messages always the email address of the profile.

Best regards
Rolf Diederichs

: : Does anyone have some references about using radial surface waves
: : from short focused transducers to detect surface and near surface
: : defects and material property variations?
: : Thanks in advance for your help.
: .
: : M. W. Moyer
: .
: Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.
.



 
 Reply 
 
Albrecht Maurer
Engineering
GE Inspection Technologies, Germany, Joined Nov 1998, 1

Albrecht Maurer

Engineering
GE Inspection Technologies,
Germany,
Joined Nov 1998
1
00:55 Feb-20-2001
Re: Radial Surface Waves
(repeated message with the profile email address, by Rolf Diederichs)

Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.

: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.



 
 Reply 
 
Dr. Patel
Dr. Patel
03:16 May-02-2001
Re: Radial Surface Waves
: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.I hope this will clarify the points. For past 3 years we are working on developing sensors and system for surface and subsurface characterization of materials in terms of surface velocities and amplitude information and we have a success. We have full facility at University which one can take advantage. The University is McMaster in Hamilton, Ontario or at Fallon Ultrasonics Inc in Hamilton.

Regards

Dr. Patel



 
 Reply 
 

Product Spotlight

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window