where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

TWI
TWI is a world leading research and technology organisation established in 1946. From bases in the UK, USA, China, Malaysia, Middle East, India a ...
998 views
Technical Discussions
M. W. Moyer
M. W. Moyer
06:34 Feb-19-2001
Radial Surface Waves

Does anyone have some references about using radial surface waves
from short focused transducers to detect surface and near surface
defects and material property variations?
Thanks in advance for your help.

M. W. Moyer


 
 Reply 
 
Albrecht Maurer
Albrecht Maurer
08:48 Feb-20-2001
Re: Radial Surface Waves
: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.
Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.


 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 608

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
608
00:47 Feb-20-2001
Re: Radial Surface Waves
Mr Gripp's paper is available at:
Surface Crack Detection Using Rayleigh Waves - in immersion: A Novel Application of a Known Principle
http://www.ndt.net/article/wcndt00/papers/idn031/idn031.htm

Also I would like to take the opportunity to introduce a problem of the email address used in the forum message.
Albrecht Maurer used in his message the email address "albrecht_maurer@nukem.de",
but his Member Profile is registers with the email address "Nutronik@Nukem.de".
The system can set Profile and Exhibitors links only according to the registered Forum Profiles.

Mr. Maurer's Profile: http://www.ndt.net/wshop/profile/profiles/123.htm
NUKEM Nutronik GmbH: http://www.ndt.net/exhibit/stand/15_ky.htm

That means you shall use for forum messages always the email address of the profile.

Best regards
Rolf Diederichs

: : Does anyone have some references about using radial surface waves
: : from short focused transducers to detect surface and near surface
: : defects and material property variations?
: : Thanks in advance for your help.
: .
: : M. W. Moyer
: .
: Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.
.



 
 Reply 
 
Albrecht Maurer
Engineering
GE Inspection Technologies, Germany, Joined Nov 1998, 1

Albrecht Maurer

Engineering
GE Inspection Technologies,
Germany,
Joined Nov 1998
1
00:55 Feb-20-2001
Re: Radial Surface Waves
(repeated message with the profile email address, by Rolf Diederichs)

Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.

: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.



 
 Reply 
 
Dr. Patel
Dr. Patel
03:16 May-02-2001
Re: Radial Surface Waves
: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.I hope this will clarify the points. For past 3 years we are working on developing sensors and system for surface and subsurface characterization of materials in terms of surface velocities and amplitude information and we have a success. We have full facility at University which one can take advantage. The University is McMaster in Hamilton, Ontario or at Fallon Ultrasonics Inc in Hamilton.

Regards

Dr. Patel



 
 Reply 
 

Product Spotlight

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Magnetic X-Ray Pipeline Crawler

Zhong Yi brand pipeline crawler is magnetic/micro-video controlled crawler with DC X ray unit inst
...
alled for checking welding of pipeline. Move steadily inside the pipeline 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometers and provide the efficient inspection of the pipeline.
>

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window