where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1106 views
Technical Discussions
UT Guy
UT Guy
03:37 Feb-20-2001
Guided Ultrasonics

Does anyone have any experience with guided ultrasonics. Please post any info you may have on this topic.


    
 
 Reply 
 
Wieslaw Bicz
Wieslaw Bicz
00:32 Feb-21-2001
Re: Guided Ultrasonics
: Does anyone have any experience with guided ultrasonics. Please post any info you may have on this topic.
.
We have large experience with waveguides filled with water. Have even patented some soultions. If we can help you.

Wieslaw Bicz

(http://www.optel.com.pl)



    
 
 Reply 
 
John Harrison
John Harrison
01:55 Feb-21-2001
Re: Guided Ultrasonics
TWI has developed Teletest, a long-range guided wave UT system for inspecting pipe. TWI’s subsidiary, Plant Integrity Ltd markets the system. It was developed for detecting corrosion under insulation, but is finding wider application to pipes in road crossings, buried pipe, jetty lines, etc. Range is typically 30m from the transducer location in either direction. Up to 175m has been achieved. 100% of the pipe wall is inspected. The system can reliably detect metal loss flaws representing 9% of the total cross sectional area of the pipe. It can also distinguish between corrosion and other pipe features, particularly welds.

Contact details are: -
Plant Integrity Ltd
Granta Park
Great Abington
Cambridge CB1 6AL
UK

Tel +(44) 1223 893994
Fax +(44) 1223 893944


    
 
 Reply 
 
Richard Finlayson
Director, Operations
Princeton Instruments, USA, Joined Jun 2000, 8

Richard Finlayson

Director, Operations
Princeton Instruments,
USA,
Joined Jun 2000
8
04:49 Feb-21-2001
Re: Guided Ultrasonics
: Does anyone have any experience with guided ultrasonics. Please post any info you may have on this topic.
.
We have a great deal of experience in guided wave testing at Physical Acoustics Corp. We are currently under contract for two companies to develop Guided Wave technology for inspecting heat exchanger tubes. Under these contracts we are developing better ways to detect corrosion in carbon steel and thermal cracks in Inconel. If you would like to reply to my email I can supply you with more details.
Richard


    
 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 278

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
278
07:59 Feb-21-2001
Re: Guided Ultrasonics
Please be more specific about the application. there are so many references in this particular field. The technology is a 'hot topic' presently due to the number of companies promoting Guided or Long Range Ultrasonics for fast screening of either above ground or buried piping.

Be careful because there is a great degree of what can and cannot be accomplished with the varying commercial flavours of this technology. This has been identified by a series of evaluations most of which are not as yet truely in the public domain.

On piping - internal & external coatings, internal liquids, geometric configuration, size and type of surrounding medium (if buried) all play a significant part in how far signals will travel in the pipe itself.

Also the technique is generally sensitive to a change in cross sectional area which can mean you need a quite substantial wall loss before you can discriminate defects. It is a screening technology with a lot of plus factors but also a number of limitations.

Insight from theBritish Institute Of NDT has covered a number of papers in their February 2001 issue. Be cautious as they are all from commercial exponents of the technology so be prepared to dissect the reported data and develop your own questions.


    
 
 Reply 
 
Xander van der Veeke
Xander van der Veeke
03:55 Jul-08-2001
Re: Guided Ultrasonics
Several evaluation on Guided Waves have already been done on also several system, which have been made commercially at this time. However as stated none of them are public. My interest will definitely be in these evaluation results.


    
 
 Reply 
 
Peter Philipp
Peter Philipp
09:08 Dec-19-2001
Re: Guided Ultrasonics
: Does anyone have any experience with guided ultrasonics. Please post any info you may have on this topic.


Guided Ultrasonics Ltd. has developed second generation long range ultrasonic test equipment using guided waves.

The development has been carried out by the original researchers of the technique who have worked with it for approximately 10 years.

The main differences in this second generation equipment is that it mainly uses torsional mode which is not affected by liquid in fully filled pipes. it needs 33 percent fewer transducers and can operate at lower frequencies as it transmits a non-dispersive wave mode.

This equipment, Wavemaker SE16 is totally portable, and battery powered. The software is totally integrated and allows automatic data collection and integraded report generation.

After comprehensive trials GUL Wavemaker SE16 equipment is now accepted by the major plant operators as the industry standard and is in commercial use worldwide.

More information is available on our website.



    
 
 Reply 
 

Product Spotlight

ISONIC 3510

Very Powerful Superior Performance Extremely Portable Smart Phased Array Ultrasonic Flaw Detector an
...
d Recorder with 2 Conventional UT and TOFD Channels uniquely combines PA, single- and multi-channel conventional UT, and TOFD modalities providing 100% raw data recording and imaging. Suitable for all kinds of every-day ultrasonic inspections
>

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Aerospace Systems - Automated Ultrasonic Inspection

USL are specialists in the design and manufacture of turnkey ultrasonic inspection systems for aer
...
ospace applications. From monolithic composites to complex honeycomb structures. This video shows just a few examples of what is possible, find out more at: www.ultrasonic-sciences.co.uk
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window