where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1418 views
Technical Discussions
Matt Clark
Matt Clark
09:40 Mar-01-2001
Tank Inspection

I have a small dilema. Could anyone advise as to a specification or procedure for the on-line inspection of storage tanks for the oil inductry. I am aware of specifications API 653 & API-RP12R1, but do not have copies or familiar with them. We are conncerned with the thickness and corrosion conditions. I would welcome any comments regarding the standard requirements needed to satisfy a continuation of use. Thanks in anticipation.


 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 280

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
280
00:16 Mar-01-2001
Re: Tank Inspection
It will depend upon your jursdiction and which is the determining component of the tank.

653 gives clear guidance on external ultrasonic thickness measurement, plus visual and settelement figures for the shell and roof all of which are accessible on line.

The floor is usually the difficult area as it is not generally accessible in service.

API 653 deals with this on either a fixed shutdown interval or perform and RBI analysis to determine the relevent inspection interval.

There are other tools that can be used on line such as submersible robots ( very expensive) or Acoustic Emission.

EEMUA in Europe is the only agency to issue clear rules on the application of Ae for corrosion assessment of storage tank floors on-line.

Often you may want to integrate AE testing into an overall RBI analysis.

If you need more specific data please contact me.


 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
03:11 Mar-01-2001
Re: Tank Inspection
: I have a small dilema. Could anyone advise as to a specification or procedure for the on-line inspection of storage tanks for the oil inductry. I am aware of specifications API 653 & API-RP12R1, but do not have copies or familiar with them. We are conncerned with the thickness and corrosion conditions. I would welcome any comments regarding the standard requirements needed to satisfy a continuation of use. Thanks in anticipation.

The thickness and corrosion measurements can be done with ultrasonic thickness gauges having a A-scan display in addition to the usual digital readout, so that the interface of the good and the corroded metals can be seen by its echo. Quantitative specifications of how much corrosion is acceptable can be found from the appropriate specifications and safety agencies. I will be happy to discuss more if needed - Swamy
.



 
 Reply 
 
Michael Trinidad
Consultant,
LMATS Pty Ltd , Australia, Joined Jan 2003, 141

Michael Trinidad

Consultant,
LMATS Pty Ltd ,
Australia,
Joined Jan 2003
141
04:19 Mar-02-2001
Re: Tank Inspection
To perform a tank inspection to API-653 requires several codes (API 575, 650, 651, 652, 653, 2015, 2207, ASME V and IX). The codes tend to refer to each other especially 653 and 650.

The new syllabii is available from the link below.


Kindest Regards


Michael Trinidad



 
 Reply 
 
Richard Kazares
Richard Kazares
09:16 Mar-02-2001
Re: Tank Inspection
In addition to manual methods, automated UT offers a resonable cost - and VERY rapid means of performing on-line UT inspection for tanks and many other similar strucutures. The many advantages of using automated systems is the ability to obtian full imaging data of your inspected areas - including very large areas if conditions warrant. The amount of information and insight into the material is significantly greater than through manual A-Scan techniques.

You can check examples of this type of inspection at our website at www.scanningsystems.com - which is now a part of NDT Automation.

: : I have a small dilema. Could anyone advise as to a specification or procedure for the on-line inspection of storage tanks for the oil inductry. I am aware of specifications API 653 & API-RP12R1, but do not have copies or familiar with them. We are conncerned with the thickness and corrosion conditions. I would welcome any comments regarding the standard requirements needed to satisfy a continuation of use. Thanks in anticipation.
.
: The thickness and corrosion measurements can be done with ultrasonic thickness gauges having a A-scan display in addition to the usual digital readout, so that the interface of the good and the corroded metals can be seen by its echo. Quantitative specifications of how much corrosion is acceptable can be found from the appropriate specifications and safety agencies. I will be happy to discuss more if needed - Swamy
: .
.



 
 Reply 
 
Azhatr Qadri
Azhatr Qadri
04:34 Apr-18-2001
Re: Tank Inspection
We are in the process in evluating the difference between Magnetic TFT and AE equipment. Please advise what is better in tems of cost and performance. Please also advise where one can purcahse these equipment second hand.

Regards

Azhar Qadri


 
 Reply 
 
John O Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 280

John O Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
280
09:33 Apr-19-2001
Re: Tank Inspection
You cannot compare TFT and AE they serve totally different functions.
You apply AE as a on-line Tank Floor condition assessment tool to determine when and on what priorities to shutdown a storage tank. It is a risk assessment tool.
This approach saves you money on not taking good tanks out of service too early.

TFT is something you need to do once the decision has been made to take the tank out of service and you use it to identify areas and extent of repairs.

There are a number of TFT Manufacturers
Silverwing UK
MFE Enterprises USA
AEA Sonomatic UK
Rosen Inspection Netherlands

Some have advantages and disadvantages based on plate thickness, reporting and internal floor coatings so choose carefully. Second hand equipment you may need to speak to the manufacturers or trawl the internet.

AE test equipment is much more specialised. The issue is not just one of recording data signals. Experience, interpretation and access to a database of past tests is much more important. Look at thereport on NDT Net from Shell under How Reliable Is AE tank testing ECNDT Denmark.

This higlights how important experience is.


 
 Reply 
 

Product Spotlight

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Ultrasonic Probe Recharacterization Service

NDT Systems offers a comprehensive Aftercare and Recharacterization Service for all our ultrasonic
...
probes. The Recharacterization Service is fully compliant with International ASTM E1065 Standard Guide (and other applicable standards) and offers complete documentation, traceable to the ASTM E1065 Standard. For more details or to schedule Recharacterization Services contact ndtsales@ndtsystems.com
>

VOGT Ultrasonics awarded innovation champion

Let go of the old and try something new. VOGT convinced the jury in the 27th round of the TOP 100
...
innovation competition. Our team is very pleased to officially belong to the TOP 100 in Germany!
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window