where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1082 views
Technical Discussions
M. W. Moyer
M. W. Moyer
06:34 Feb-19-2001
Radial Surface Waves

Does anyone have some references about using radial surface waves
from short focused transducers to detect surface and near surface
defects and material property variations?
Thanks in advance for your help.

M. W. Moyer


 
 Reply 
 
Albrecht Maurer
Albrecht Maurer
08:48 Feb-20-2001
Re: Radial Surface Waves
: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.
Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.


 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 617

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
617
00:47 Feb-20-2001
Re: Radial Surface Waves
Mr Gripp's paper is available at:
Surface Crack Detection Using Rayleigh Waves - in immersion: A Novel Application of a Known Principle
http://www.ndt.net/article/wcndt00/papers/idn031/idn031.htm

Also I would like to take the opportunity to introduce a problem of the email address used in the forum message.
Albrecht Maurer used in his message the email address "albrecht_maurer@nukem.de",
but his Member Profile is registers with the email address "Nutronik@Nukem.de".
The system can set Profile and Exhibitors links only according to the registered Forum Profiles.

Mr. Maurer's Profile: http://www.ndt.net/wshop/profile/profiles/123.htm
NUKEM Nutronik GmbH: http://www.ndt.net/exhibit/stand/15_ky.htm

That means you shall use for forum messages always the email address of the profile.

Best regards
Rolf Diederichs

: : Does anyone have some references about using radial surface waves
: : from short focused transducers to detect surface and near surface
: : defects and material property variations?
: : Thanks in advance for your help.
: .
: : M. W. Moyer
: .
: Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.
.



 
 Reply 
 
Albrecht Maurer
Engineering
GE Inspection Technologies, Germany, Joined Nov 1998, 1

Albrecht Maurer

Engineering
GE Inspection Technologies,
Germany,
Joined Nov 1998
1
00:55 Feb-20-2001
Re: Radial Surface Waves
(repeated message with the profile email address, by Rolf Diederichs)

Mr. Sebastian Gripp of our organisation has realized an industrial solution for surface testing of contoured turbine discs applying a specific rayleigh wave probe. The corresponding paper has been presented at the WCNDT in Rome last fall.

: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.



 
 Reply 
 
Dr. Patel
Dr. Patel
03:16 May-02-2001
Re: Radial Surface Waves
: Does anyone have some references about using radial surface waves
: from short focused transducers to detect surface and near surface
: defects and material property variations?
: Thanks in advance for your help.
.
: M. W. Moyer
.I hope this will clarify the points. For past 3 years we are working on developing sensors and system for surface and subsurface characterization of materials in terms of surface velocities and amplitude information and we have a success. We have full facility at University which one can take advantage. The University is McMaster in Hamilton, Ontario or at Fallon Ultrasonics Inc in Hamilton.

Regards

Dr. Patel



 
 Reply 
 

Product Spotlight

On Demand Webinar: Improve the Efficiency and Accuracy of Inspection Scanning

On-demand webinar on scanning technology that helps improve the efficiency and accuracy of ultrasoni
...
c inspections in oil and gas, aerospace, manufacturing and other industrial applications. The webinar features a scanning solution for multiple inspection environments, including flat and curved specimens, magnetic and nonmagnetic surfaces and raster scanning over long distances. View it today.
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

MANTIS

MANTIS is a compact, powerful and affordable flaw detector (16:64PR), dedicated to field operators
...
. This portable equipment offers standard (electronic-, sector-, compound scan, conventional UT for pulse-echo, dual array and TOFD inspections), and advanced phased-array (real-time TFM -Total Focusing Method). MANTIS benefits from the same intuitive and user-friendly interface (CAPTURE) than Gekko for easier inspections.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window