|Rolf D. |
NDT.net, Germany, Joined Nov 1998, 605
To all: Is there any disadvantage for composite transducers? The great advantages which were pointed out in articles from G. Fleury 
and G. Splitt  lead to the conclusion,
to use only composite transducers from now on, is this right?
In particularly, is there any figure of the following
table which result also in disadvantages.
comparison: lead zirco-titanate PZT ---> 1-3 composite Is that design available for any frequencies,
acoustical impedance (Mray): 30-32 ---> 8-12
coupling coefficient: 0.45 ---> 0.5-0.7
dielectrical constant: 250-2000 ---> 200-600
density (g/cm3): 7.8 ---> 3.5-4
and is this design beneficially for any frequencies?Is that kind of transducer more expensive,
and how much does it share with the total transducer market?
That are of course a lot of questions.
I would appreciate if other experts will give their comments as well,
however let us first wait for Mr. Fleury's answer.
IMPROVEMENTS OF ULTRASONIC INSPECTIONS THROUGH THE USE OF
Transducers with Piezo Composite - a milestone for Ultrasonic Testing
|Bill Grandia |
Re: To all: Is there any disadvantage for composite transducers? The composite transducer has both advantages and disadvantages. The positive aspects were outlined by G. Fleury and G. Splitt. There are some applications were this extremely nice device is less desirable. To realize what the disadvantages are, requires to analyze the differences in characteristics as compared to conventional transducers.
The name composite transducers means that a solid piezo-electric element has been modified. There a basically two ways to construct a composite element.
a) A solid piezo disk can be broken in small pieces or granules, whereby the spaces between the granules are filled with epoxy. A preferred filler seems to be Spurr epoxy, which in liquid state has a very low viscosity (like water).
A focused composite element can simply be produced by inserting a solid polarized element between concave and convex shaped press-mold halves, hereby submerging the entire mold in liquid epoxy. This method allows the epoxy to flow into the crevices and prevents air from entering into the crushed structure. After the epoxy is cured, the dish-shaped element can be taken out of the mold. Of course, the electrodes need to be restored. There is no need to re-polarize the element, since the granules are staying in their original alignment.
This construction is less popular, since the fill factor for the element is practically fixed. The only feature is that the radial to the thickness mode becomes uncoupled. By this, the effectiveness of the thickness mode vibration is enhanced. There is virtually no reduction in acoustic impedance and dielectric constant. The bandwidth of the element is becomes increased. When a high "Q" element such as PZT5A is used, the signal response of the crushed version more or less behaves like a lead metaniobate element, except that the sensitivity is stronger.
b) A better method is the dicing approach, whereby the element is cut into small pieces and has been described in detail by G. Fleury and G.Splitt.
We need to discuss the disadvantages.
1: The composite element is not desired when a high "Q: transducer is necessary. A "high "Q" means that the transducer has a narrow bandwidth and therefor produces a large amount of ringing. The penetration power of a high Q transducer is strong. When highly attenuative materials are to be inspected, a strong signal is required. Sometimes this can be enhanced by applying a toneburst signal with a frequency equal to the series resonance frequency of the element. At this resonant condition, the electrical impedance of the device becomes minim and therefor the generated sound pressure into the material is strongly enhanced. This is not possible with diced elements. From a receiving standpoint, a strong signal can also be obtained in the narrow band mode. The narrow band application is very popular for the through transmission technique.
2: The composite transducer is less suited as a direct contact transducer for the inspection of steel or ceramics, especially when the transducer needs to be wear resistant.
The lowered acoustical impedance is not impedance matched to the ceramic wearplate or the steel surface.
3: Another characteristic of composite transducers it that the capacitance of the element reduces with the aspect ratio of the total area of the diced elements and the filler epoxy. When this ratio becomes high while trying to make a low acoustic impedance (like good matching to water), the electrical charge produced on the diced element from a reflected signal becomes small. When a long coaxial cable is connected to the transducer, the signal amplitude becomes small. The cable acts now like a parallel capacitance, hereby absorbing the signal to an appreciable extend. Typically, the capacitance of a coaxial cable is 31 pFd / foot. A 10 foot cable therefor is 310 pFd. If the element capacitance is around 300 pFd, the signal amplitude drops to half the value. Of coarse, the can be overcome by using an high input impedance low noise pre-amplifier located very close bythe transducer. It is possible to use such pre-amplifiers in the pulse echo mode by inserting an isolation circuit to protect the amplifier from the large damaging transmitting pulse. The use of such an amplifier greatly enhances the performance of the composite transducer by preserving the high resolution wave shape.
This sumps up the few disadvantages of the composite transducers.
|Fleury Gerard |
Re: To all: Is there any disadvantage for composite transducers? s acoustically loaded by a low impedance
medium even when the material or the piece to be inspected has a high impedance : for instance in the
case of immersion probes and probes incorporating (or associated with) a shoe, a wedge or a delay line.
made of polymer materials.In these numerous cases
transducers with an active part made of 1-3 piezocomposite material can provide better sensitivity
in a wider freqency band than transducers produced with other presently known technologies. Such transducers can bring an important improvement in inspection quality ( see for instance results given in workshop articles from G.Splitt and G.Fleury ) in applications where signal to noise ratio and bandwidth
are critical parameters .
Of course composite transducers have some limitations and yet Bill Grandia noticed some of them .
The case of applications where the transducer is
used in direct and intimate contact with a high impedance material is one of them . Due to their relatively low acoustic impedance, piezocomposite materials may be not appropriate to build such transducers.
The case of applications" requiring High Q transducers" should be discussed into more details :
Is the High Q required to create a narrow band or
is it only a way to design an efficient transducer (at
a given frequency) and /or to transmit high intensity
If the application imposes a narrow band system ,this narrow band can be obtained by different ways :
. Narrow band transducer is one way to do it and then
composite technology may be not appropriate to get
it .However in such case the frequency will be fixed
by transducer design,dependant from manufacturing tolerances and may be will vary with temperature or
transmitted power ( which creates heating effects
inside the transducer)
. Narrow band of the system can be obtained by electronic filtering associated with a medium or wide band transducer and then the frequencycan be more easily choosen and controlled.
If the application requires an efficient transducer,then
composite transducer can be extremely useful with a high transmit/receive efficiency quite close to what can produce narrow band transducers and again with the possibility to adjust and/or control the frequency.
Finally, if the application requires power generation
then specially designed composite transducers can
produce very high level of intensities in CW, high duty
cycle burst or impulse mode .
Are composite transducers more expensive than conventional ones ? Such question requires special
attention about the basis of comparisons :
.Is the comparison to be done on standardised probes manufactured with the same general specifications excepted acoustical properties? Then, as far as I know, differences in prices are quite low between composite transducers and conventional transducers and I am not able to say if the difference is due to the composite aspect or is due to other aspects as for instance general quality or associated services .
.On special transducers dedicated to special applications the analysis is still more difficult to do
but again as far as I know differences in price are not important in comparison with the gain on global functional performances.
Limitations in frequency :
Piezocomposite technology based on 1-3 active
materials is physically limited in frequency due to the
microstructure of materials .As far as I know the upper
limit is a center frequency of 15 Mhz for standard transducers and 18 Mhz for special fabrications .
There are many other things ( array applications ,low frequency transducers,aspherical focusing,high temperature, ...) to discuss about composite transducers but excepted the above comments I do not see many restrictions for the use of
such transducers in NDE applications.Of course these
transducers are presently a small part of the total market of transducers but they bring so much advantages in many applications that I am sure they
will play a much more important role in the future .
|Gerhard Splitt |
R & D, -
Private, Germany, Joined Nov 1998, 38
Re: To all: Is there any disadvantage for composite transducers?
Sorry for the delayed answer which is due to too much trouble last week.
The comments of Bill Grandia have shown that piezocomposite transducers are
suitable for nearly all probes except for hardfaced probes, which will be coupled
directly to steel. But even there could be some advantage depending on crystal
diameter, frequency and wear plate material. A normal PZT transducer will produce
radial ringing which can result in spurious echos in the hardface probe. With a
piezocomposite transducer the radial coupling is reduced to a small amount making
the hardface probe more quiet.
Of course there are some other restrictions for using piezocomposite transducers for
all types of probes.
1. The material is more costly, therefore it will not be used in cheap probes.
2. It is difficult and extremely costly to fabricate high frequency transducers. To avoid
additional ringing the periodicity of the 1-3 piezocomposite matrix should be smaller
than halve the wavelength of shear waves in the epoxy matrix for the highest
frequency within the pass band of the probe. For 15 MHz probe e.g. this results in
very small ceramic posts of 0.04 mm edge length and very small separating epoxy
lines of 0.015 mm (for 20 MHz upper pass band and shear wave velocity of 1100
3. Piezocomposite material is not suitable for temperatures above 130 degree C
In high volume industries like automotive the requirement for a
hundred percent X-ray inspection c
reates a bottleneck in the
production. The XRHRobotStar is a fully Automated Defect Recognition
(ADR) capable robot-system that allows an ultra-fast in-line
ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates.
All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs.
Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
NDTkit RT, TESTIA's Digital Radiography software
The NDTkit product line software for X-ray analysi
NDTkit RT is a software benefiting from the Ultis kernel which is
dedicated to radiographic image analysis. It offers a set of tools
and filtering processes to assist RT operators in finding relevant
The all-digital Novascope 6000 is a portable, ultra-high precision
thickness gauge for high-speed
Novascope 6000 has unmatched capabilities and unique features
•Superior Resolution with high contrast, high-speed color RF
•High pulser voltage
•Real-time video output
•Increased internal/external data storage
•Programmable SetUp features
•Battery & AC Powered