where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
553 views
Technical Discussions
Atul Deulgaonkar
Atul Deulgaonkar
07:44 May-19-2001
Ultrasonic testing of forged shaft

While testing it is observed a number of times that shafts do not give any back wall echo even at full gain and using probes of very low fequencies like 1Mhz or 0.5Mhz.
What is interpretation of this phenomenon ?


 
 Reply 
 
Anonymous
Anonymous
01:27 May-19-2001
Re: Ultrasonic testing of forged shaft
: While testing it is observed a number of times that shafts do not give any back wall echo even at full gain and using probes of very low fequencies like 1Mhz or 0.5Mhz.
: What is interpretation of this phenomenon ?
.
Try various Pulse Repitition Rates and a 2.25 MHz. Transducer.


 
 Reply 
 
Dr. Patel
R & D, Consultant to Universities/Industries
Fallon Ultrasonics/McMaster University, Canada, Joined May 2001, 20

Dr. Patel

R & D, Consultant to Universities/Industries
Fallon Ultrasonics/McMaster University,
Canada,
Joined May 2001
20
06:44 May-19-2001
Re: Ultrasonic testing of forged shaft
: : While testing it is observed a number of times that shafts do not give any back wall echo even at full gain and using probes of very low fequencies like 1Mhz or 0.5Mhz.
: : What is interpretation of this phenomenon ?
: .
: Try various Pulse Repitition Rates and a 2.25 MHz. Transducer.

There are many reasons for that and if you can send us details on probe diameter and contact face, PRF and energy on your pulser, perhaps we can help you interprete the phenomenon. Beam divergence, contact losses, losses due to material properties etc plays a role, however, first we have to establish the sensor and instrument you are using is OK than we can deal with other problems.

Regards

Dr. Patel



 
 Reply 
 

Product Spotlight

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Echomac® Small

Available with up to eight channels of electronics to detect and evaluate thickness, flaws and eccen
...
tricity, this UT tester is housed in a convenient, smaller cabinet. This instrument can be used in conjunction with bubbler or immersion tank systems, or with a test bench or in laboratory applications. The Echomac® Small is available in the FD4, FD6 or FD6A versions.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window