where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1179 views
Technical Discussions
aldo
Engineering
Italy, Joined Jan 2009, 39

aldo

Engineering
Italy,
Joined Jan 2009
39
18:46 Feb-09-2009
torioidal magetization

Hi everybody. I am studying the induced current magnetization especially the todoidal method for ring shapdes part on aeronautic components. I have a lot of questions for the forum specialist on specific ASTM par. 6.2.9 in particular on ratio between L/D. The following questions are:
1)What diameter do i take of the part? outside diameter Dout, inner diameter Din or effective diameter Deff?
2)The specific saies that ratio L/D must be less than three. Why? Whats happens if i choose a conponent wich have a ratio L/D major than three? I think that with a ratio major than three i have a overheat on component. Is correct my interpretation ?
Tanks and best regards
Aldo

 
 Reply 
 
aldo
Engineering
Italy, Joined Jan 2009, 39

aldo

Engineering
Italy,
Joined Jan 2009
39
19:50 Mar-02-2009
Re: torioidal magetization
In Reply to aldo at 18:46 Feb-09-2009 (Opening).

Hi everybody.
I have discovered important information on L/D ratio. On specific book of NDT of title:Nondestructive Evaluation - Theory, Techniques, and Applications - (Peter J. Shull) Marcel Dekker 2001, it indicates that L is: "lenght of iron core" while does not specific that type of diameter must be considered... can somebody help me for to define the diameter that is present on specific ASTM 6.2.9?
Tanks and best regards...
Aldo

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 891

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
891
23:07 Mar-03-2009
Re: torioidal magetization
In Reply to aldo at 19:50 Mar-02-2009 .

Aldo,

You reference paragraph 6.2.3 of an ASTM standard yet you don't mention which one it is! It is pretty hard to answer your question without this information.

 
 Reply 
 
aldo
aldo
19:50 Mar-04-2009
Re: torioidal magetization
In Reply to Michel Couture at 23:07 Mar-03-2009 .

Hi michel Couture... Tanks your replay...
Why do the ASTM not specific the type of diameter of component? Becasue there are not information on specific textbooks or technical articles on this matter...
Tanks

 
 Reply 
 
Amy
NDT Inspector, - -
USA, Joined Jan 2009, 87

Amy

NDT Inspector, - -
USA,
Joined Jan 2009
87
21:59 Mar-04-2009
Re: torioidal magetization
In Reply to aldo at 19:50 Mar-04-2009 .

Aldo,
Looking at ASTM E1444-05, for inducing a toroidal field, typically is used for ring or disc shaped parts to find circumfrential defects. It actually uses the iron core inside your part in the coil to induce an eddy current into the part. It's good if you cannot use a central conductor or do not want to risk arcing with a head shot. As far as the formula you are looking for, use the dimensions of the iron core with your base formula 45000/(l/d) for a low fill as a beginning current and attach QQI's. I've found formulas are more than unreliable and the QQI is your best bet. I usually start almost 1000 Amps lower than my calculated and increase till the QQI's show. As far as parts with a L/D greater than 3, the core is not needed. the part should have a uniform longitudinal field with the coil shot. I do a lot of ring shaped, and if you can, use a central conductor, stay away from the toroidal, or if you must do a coil, use extension pieces of the same diameter on either side to increase your L/D. Hope it helps....

 
 Reply 
 
mandar
mandar
07:35 Mar-05-2009
Re: torioidal magetization
In Reply to aldo at 19:50 Mar-04-2009 .

Dear Aldo ,
As far as my interpretation goes there is no formula for setting ampere turns for torroidal magnetization but should be set up using QQI shims or the hall effect gauss meter because in using the formulae it is stated that in L/D these values are considered of the part under test and not of the core further more it is clearly stated that the formulae hold true for parts having L/D more than 3 and less than 15 and it is clearly stated that torroidal magnetization is used for parts having L/D less than 3 hence the faormulae are not applicable for torroidal magnetization . This is mainly because the induced eddy currents dependent on all factors like fill factor of part to coil and also core with respect to part ID and also frequency of current used .

 
 Reply 
 

Product Spotlight

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

Portable Ground Penetrating Radar - Proceq GP8000

The Proceq GP8000 portable ground penetrating radar instrument is the beginning of a new era in ND
...
T. The outstanding, patented ultra- wideband technology combined with a compact wireless probe delivers unmatched industry performance. Proceq GP8000 is the world’s first large-scale inspection solution that utilizes Augmented Reality in industrial applications.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window