where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

848 views
Technical Discussions
ALI AL_DAWJI
Engineering, Doctor course student
Japan, Joined May 2001, 4

ALI AL_DAWJI

Engineering, Doctor course student
Japan,
Joined May 2001
4
06:28 May-29-2001
The volume of air bubbles

Dear Sir.
I am looking for some information related
to measure and detect the volume of air bubbles,
or voids of air (around 0.5 cubic cm) in an object
using any ultrasonic techniques,
I would be grateful if any one could help me,
by giving suitable information related to this matter.



 
 Reply 
 
Dr. Patel
R & D, Consultant to Universities/Industries
Fallon Ultrasonics/McMaster University, Canada, Joined May 2001, 20

Dr. Patel

R & D, Consultant to Universities/Industries
Fallon Ultrasonics/McMaster University,
Canada,
Joined May 2001
20
06:47 May-29-2001
Re: The volume of air bubbles
: Dear Sir.
: I am looking for some information related
: to measure and detect the volume of air bubbles,
: or voids of air (around 0.5 cubic cm) in an object
: using any ultrasonic techniques,
: I would be grateful if any one could help me,
: by giving suitable information related to this matter.
.

We have measured both in glass and liquid using ultrasonic methods and perhaps you can use the method. If you have small sample please send us and we will send you results. If it is in liquid than number of universities have purchased system from us and have a good success. Please contact me

Regards

Dr. Patel



 
 Reply 
 
Wieslaw Bicz
Engineering,
PBP Optel sp. z o.o., Poland, Joined Feb 2009, 276

Wieslaw Bicz

Engineering,
PBP Optel sp. z o.o.,
Poland,
Joined Feb 2009
276
01:10 May-29-2001
Re: The volume of air bubbles
: Dear Sir.
: I am looking for some information related
: to measure and detect the volume of air bubbles,
: or voids of air (around 0.5 cubic cm) in an object
: using any ultrasonic techniques,
: I would be grateful if any one could help me,
: by giving suitable information related to this matter.
.
For a project with the goal of early detection of breast cancer we are developing a version of our holographic camera, that is able to visualize 3D objects with high resolution.
Using the first version of this holographic camera it could be possible to measure such bubbles (with the assumption, that the amount of them is not very high) with high precision (better than 0.1mm).
It is possible to achieve very good 3D reconstruction of such objects.

If you are interested in cooperation, please contact me (w.bicz@optel.pl)




 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
05:10 May-29-2001
Re: The volume of air bubbles
: I am looking for some information related
: to measure and detect the volume of air bubbles,
: or voids of air (around 0.5 cubic cm) in an object
: using any ultrasonic techniques,

In what sort of material are you trying to detect the bubbles? How long will the sound path be between the transducer and the target bubbles? Are the bubbles of uniformly spherical shape or does the shape vary? To what level of precision do you need to determine bubble size? All of these considerations will have an effect on the feasibility and reliability of ultrasonic detection and sizing. Perhaps you could tell us a bit more about your test conditions.

--Tom Nelligan



 
 Reply 
 

Product Spotlight

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window