where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Iris Inspection Services, Inc.
We are the world's largest supplier of air cooler, boiler and exchanger tubing inspection services.
1394 views
Career Discussions
Slimmoon
Slimmoon
17:13 Mar-26-2009
Regarding NCR

Hi..
Who will fill in NCR , Root cause and corrective action . Quality ,or Production for any NC

 
 Reply 
 
Ed T.
Ed T.
02:51 Mar-27-2009
Re: Regarding NCR
In Reply to Slimmoon at 17:13 Mar-26-2009 (Opening).

In my opinion, the NCR should be filled out by the organization's QA/QC Manager or his representative that received the NCR.
It should then be reviewed after corrective action has been performed by the NCR originator and if satisfied, closed out.

 
 Reply 
 
K.Durga Rao
Consultant, - General Manager (Technical)
Asia Power Projects Pvt Ltd, India, Joined May 2009, 3

K.Durga Rao

Consultant, - General Manager (Technical)
Asia Power Projects Pvt Ltd,
India,
Joined May 2009
3
12:29 Mar-27-2009
Re: Regarding NCR
In Reply to Slimmoon at 17:13 Mar-26-2009 (Opening).

In my view it can be done in two ways; (a) If the non conformity was noticed by production department during manufacture of the goods before it was offered for inspection checks, head of that production section had to raise an NCR and that NCR had to be countersigned by the respective quality control engineer of that section. After the non conformity was attended by the production department, this had to be once again countersigned by the respective quality control engineer confirming the conformity and finally this NCR had to be closed by the management reprasentative of Quality control department. (b) If the non-conformity was noticed by the quality control engineer during his inspection, the NCR had to be raised by that quality control engineer and it had to be countersigned by the production dapartment head. Once this non coformity was resolved, the same quality control engineer had to countersign the NCR confirming the conformity and it had to be closed by the management reprasentative of Quality control department.

 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
03:45 Mar-28-2009
Re: Regarding NCR
In Reply to K.Durga Rao at 12:29 Mar-27-2009 .

Dear Durga Rao garu,

Very good advice. Both production and QA/QC are to be involved at all stages of NCR resolution.

Swamy
QA and NDT Expert

 
 Reply 
 
Abbas Bombaywala
NDT Inspector
Free Lance, India, Joined Jul 2007, 92

Abbas Bombaywala

NDT Inspector
Free Lance,
India,
Joined Jul 2007
92
06:54 Mar-29-2009
Re: Regarding NCR
In Reply to Slimmoon at 17:13 Mar-26-2009 (Opening).

Hi Dear All

I Think Design department should also be involved there should be also comments and signature from Design Department that whether it is accepted or if it is affecting some change in Design part of view then he will raise a DCR to client and upon client acceptance of that DCR the NCR will be closed.

With Regards.
Abbas Zoher

 
 Reply 
 

Product Spotlight

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Magnetic X-Ray Pipeline Crawler

Zhong Yi brand pipeline crawler is magnetic/micro-video controlled crawler with DC X ray unit inst
...
alled for checking welding of pipeline. Move steadily inside the pipeline 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometers and provide the efficient inspection of the pipeline.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window