where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1365 views
Technical Discussions
Mathew Anderson
Mathew Anderson
21:38 Apr-07-2009
Ultrasonic Thickness Gauge

Can Ultrasonic Thickness Gauges measure the thickness of glass, and if so will only the higher end models do this?

Regards

Mathew

 
 Reply 
 
TomNelligan
Engineering,
retired, USA, Joined Nov 1998, 390

TomNelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
22:21 Apr-07-2009
Re: Ultrasonic Thickness Gauge
In Reply to Mathew Anderson at 21:38 Apr-07-2009 (Opening).

Yes, any good ultrasonic thickness gage should be able to measure glass with a proper transducer and setup. You didn't indicate the range of glass thickness that you need to measure, but inexpensive corrosion gages will typically measure flat or large-radius glass over roughly the same range in which they would measure steel. You will need to calibrate sound velocity for glass, although it's usually close to that of most steel alloys. Precision gages can do much more, including wall thickness of small diameter tubing using focused immersion transducers.

We have an application note on the subject that you may find useful:
Thickness Measurement of Glass
http://www.olympus-ims.com/en/ndt-application/183-id.209715251.html

 
 Reply 
 
Neil Burleigh
Sales
Krautkramer Australia Pty Ltd, Australia, Joined Dec 2002, 159

Neil Burleigh

Sales
Krautkramer Australia Pty Ltd,
Australia,
Joined Dec 2002
159
03:05 Apr-08-2009
Re: Ultrasonic Thickness Gauge
In Reply to Mathew Anderson at 21:38 Apr-07-2009 (Opening).

To follow on from what Tom has said we would need to know a little more about the measurement application. We have had an interesting application recently regarding laminated glass windows that were installed the wrong way. The thin thickness was installed to the outside instead of the inside which meant the impact resistance was not as stated. We used a 10 MHz probe to measure the thickness of the glass to the laminate which was supposed to be 6 mm whereas it was 3 mm.

hope this gives some insight.
Regards

Neil Burleigh

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 894

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
894
06:00 Apr-08-2009
Re: Ultrasonic Thickness Gauge
In Reply to Neil Burleigh at 03:05 Apr-08-2009 .

This method is often used on aircraft windows. The windshields are laminated, so a little bit harder to do, but it can be done. I remember for the Bombardier Challengers, we had an actual step wedge made from the same material as the window. Made the job so much simpler.

I don't know about other situation, but for aircraft, since the windows are made of something similar to lexan or plexiglass, they can be blended if they are scratched. So it is important to know the exact thickness. If I remember correctly, you can only remove 10% of the thickness. But like Neil said, 10 - 15 MHz with a delay shoe should do it.

 
 Reply 
 

Product Spotlight

32:128PR PAUT & 2-ch TOFD Flaw Detector: SyncScan 2

●32:128PR PAUT with optional 2-ch TOFD to maximize your efficiency ●Support PR mode for corrosi
...
on inspection ●Multiple solutions for welds & corrosion ●Faster scan speed (Approximately 3 meters/minute) ●Light weight: 4kg only including battery
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window