where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

GB Inspection Systems Ltd.
A leading UK manufacturer of Ultrasonic Probes, Accessories, Supplier of NDT Equipment and more.
1258 views
Technical Discussions
Mathew Anderson
Mathew Anderson
21:38 Apr-07-2009
Ultrasonic Thickness Gauge

Can Ultrasonic Thickness Gauges measure the thickness of glass, and if so will only the higher end models do this?

Regards

Mathew

    
 
 Reply 
 
TomNelligan
Engineering,
retired, USA, Joined Nov 1998, 390

TomNelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
22:21 Apr-07-2009
Re: Ultrasonic Thickness Gauge
In Reply to Mathew Anderson at 21:38 Apr-07-2009 (Opening).

Yes, any good ultrasonic thickness gage should be able to measure glass with a proper transducer and setup. You didn't indicate the range of glass thickness that you need to measure, but inexpensive corrosion gages will typically measure flat or large-radius glass over roughly the same range in which they would measure steel. You will need to calibrate sound velocity for glass, although it's usually close to that of most steel alloys. Precision gages can do much more, including wall thickness of small diameter tubing using focused immersion transducers.

We have an application note on the subject that you may find useful:
Thickness Measurement of Glass
http://www.olympus-ims.com/en/ndt-application/183-id.209715251.html

    
 
 Reply 
 
Neil Burleigh
Sales
Krautkramer Australia Pty Ltd, Australia, Joined Dec 2002, 158

Neil Burleigh

Sales
Krautkramer Australia Pty Ltd,
Australia,
Joined Dec 2002
158
03:05 Apr-08-2009
Re: Ultrasonic Thickness Gauge
In Reply to Mathew Anderson at 21:38 Apr-07-2009 (Opening).

To follow on from what Tom has said we would need to know a little more about the measurement application. We have had an interesting application recently regarding laminated glass windows that were installed the wrong way. The thin thickness was installed to the outside instead of the inside which meant the impact resistance was not as stated. We used a 10 MHz probe to measure the thickness of the glass to the laminate which was supposed to be 6 mm whereas it was 3 mm.

hope this gives some insight.
Regards

Neil Burleigh

    
 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 848

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
848
06:00 Apr-08-2009
Re: Ultrasonic Thickness Gauge
In Reply to Neil Burleigh at 03:05 Apr-08-2009 .

This method is often used on aircraft windows. The windshields are laminated, so a little bit harder to do, but it can be done. I remember for the Bombardier Challengers, we had an actual step wedge made from the same material as the window. Made the job so much simpler.

I don't know about other situation, but for aircraft, since the windows are made of something similar to lexan or plexiglass, they can be blended if they are scratched. So it is important to know the exact thickness. If I remember correctly, you can only remove 10% of the thickness. But like Neil said, 10 - 15 MHz with a delay shoe should do it.

    
 
 Reply 
 

Product Spotlight

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Magnetic X-Ray Pipeline Crawler

Zhong Yi brand pipeline crawler is magnetic/micro-video controlled crawler with DC X ray unit inst
...
alled for checking welding of pipeline. Move steadily inside the pipeline 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometers and provide the efficient inspection of the pipeline.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window