where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
2073 views
Technical Discussions
Jan Verkooijen
Director,
Sonovation, Netherlands, Joined Nov 1998, 29

Jan Verkooijen

Director,
Sonovation,
Netherlands,
Joined Nov 1998
29
01:22 May-25-2001
ASNT's SNT-TC-1a

We have a bit of a discussion at the moment on the interpretation
of the SNT-TC-1a. According to the document, people wishing to
become a UT level II operator, should sit a specific examination with
a minimum of 20 questions "addressing the equipment, operating procedures
and NDT techniques that the individual may encounter during specific
assignments..". Our staff work to several codes and standards. Does
this mean they have to sit an exam with 20 questions on each standard
or procedure or is it sufficient to cover different codes and standards
in the questions. By example 5 questions on German standards, 5 on Dutch,
5 on ASME etc? Is there a minimum of questions on the standards at all,
because the 20 questions should also cover the equipment etc?

Talking to some collegues this appears to be an issue for more training
institutes and NDT companies. I would therefore appreciate some advise
on the above.

Thanks,

Jan Verkooijen


 
 Reply 
 
Fred Raco
Director
CP Industries - Div. of Reunion Industries, Inc., USA, Joined Jan 2001, 6

Fred Raco

Director
CP Industries - Div. of Reunion Industries, Inc.,
USA,
Joined Jan 2001
6
03:39 May-25-2001
Re: ASNT's SNT-TC-1a
Dear Jan Verkooijen,

The specific examination shall consist of a minimum of 20 questions to meet the requirements of SNT-TC-1A. If you or your organization feel that 20 questions is not enough to properly cover the broad range of specifications, equipment, techniques and so on, you may put as many questions as you like on the exam.

Good luck and best regards,

Fred Raco
Director NDT
CP Industries

: We have a bit of a discussion at the moment on the interpretation
: of the SNT-TC-1a. According to the document, people wishing to
: become a UT level II operator, should sit a specific examination with
: a minimum of 20 questions "addressing the equipment, operating procedures
: and NDT techniques that the individual may encounter during specific
: assignments..". Our staff work to several codes and standards. Does
: this mean they have to sit an exam with 20 questions on each standard
: or procedure or is it sufficient to cover different codes and standards
: in the questions. By example 5 questions on German standards, 5 on Dutch,
: 5 on ASME etc? Is there a minimum of questions on the standards at all,
: because the 20 questions should also cover the equipment etc?
.
: Talking to some collegues this appears to be an issue for more training
: institutes and NDT companies. I would therefore appreciate some advise
: on the above.
.
: Thanks,
.
: Jan Verkooijen
.



 
 Reply 
 
Jan Verkooijen
Director,
Sonovation, Netherlands, Joined Nov 1998, 29

Jan Verkooijen

Director,
Sonovation,
Netherlands,
Joined Nov 1998
29
09:42 May-28-2001
Re: ASNT's SNT-TC-1a
Dear Fred,

Would an ASME authorised inspector generally accept this, or
would he demand a minimum of for example say 15 questions
dealing with ASME? To my idea it would be up to the company
to detail in their written practice, but is there any jurisdiction
on this?

Best regards,

Jan Verkooijen

: Dear Jan Verkooijen,
.
: The specific examination shall consist of a minimum of 20 questions to meet the requirements of SNT-TC-1A. If you or your organization feel that 20 questions is not enough to properly cover the broad range of specifications, equipment, techniques and so on, you may put as many questions as you like on the exam.
.
: Good luck and best regards,
.
: Fred Raco
: Director NDT
: CP Industries
.
.
.
.
: : We have a bit of a discussion at the moment on the interpretation
: : of the SNT-TC-1a. According to the document, people wishing to
: : become a UT level II operator, should sit a specific examination with
: : a minimum of 20 questions "addressing the equipment, operating procedures
: : and NDT techniques that the individual may encounter during specific
: : assignments..". Our staff work to several codes and standards. Does
: : this mean they have to sit an exam with 20 questions on each standard
: : or procedure or is it sufficient to cover different codes and standards
: : in the questions. By example 5 questions on German standards, 5 on Dutch,
: : 5 on ASME etc? Is there a minimum of questions on the standards at all,
: : because the 20 questions should also cover the equipment etc?
: .
: : Talking to some collegues this appears to be an issue for more training
: : institutes and NDT companies. I would therefore appreciate some advise
: : on the above.
: .
: : Thanks,
: .
: : Jan Verkooijen
: .
.



 
 Reply 
 
Fred Raco, Jr.
Director
CP Industries - Div. of Reunion Industries, Inc., USA, Joined Jan 2001, 6

Fred Raco, Jr.

Director
CP Industries - Div. of Reunion Industries, Inc.,
USA,
Joined Jan 2001
6
03:42 May-29-2001
Re: ASNT's SNT-TC-1a
It is hard to tell what your ASME Inspector will do. Ask him what he prefers and attempt to accommodate him. There is no justification noted in TC-1A. However, I have seen other codes that add to the minimum requirements such as MIL-STD-271.

Dear Fred,
.
: Would an ASME authorised inspector generally accept this, or
: would he demand a minimum of for example say 15 questions
: dealing with ASME? To my idea it would be up to the company
: to detail in their written practice, but is there any jurisdiction
: on this?
.
: Best regards,
.
: Jan Verkooijen
.
: : Dear Jan Verkooijen,
: .
: : The specific examination shall consist of a minimum of 20 questions to meet the requirements of SNT-TC-1A. If you or your organization feel that 20 questions is not enough to properly cover the broad range of specifications, equipment, techniques and so on, you may put as many questions as you like on the exam.
: .
: : Good luck and best regards,
: .
: : Fred Raco
: : Director NDT
: : CP Industries
: .
: .
: .
: .
: : : We have a bit of a discussion at the moment on the interpretation
: : : of the SNT-TC-1a. According to the document, people wishing to
: : : become a UT level II operator, should sit a specific examination with
: : : a minimum of 20 questions "addressing the equipment, operating procedures
: : : and NDT techniques that the individual may encounter during specific
: : : assignments..". Our staff work to several codes and standards. Does
: : : this mean they have to sit an exam with 20 questions on each standard
: : : or procedure or is it sufficient to cover different codes and standards
: : : in the questions. By example 5 questions on German standards, 5 on Dutch,
: : : 5 on ASME etc? Is there a minimum of questions on the standards at all,
: : : because the 20 questions should also cover the equipment etc?
: : .
: : : Talking to some collegues this appears to be an issue for more training
: : : institutes and NDT companies. I would therefore appreciate some advise
: : : on the above.
: : .
: : : Thanks,
: : .
: : : Jan Verkooijen
: : .
: .
.



 
 Reply 
 
Ken
Senior Level III
USA, Joined Jan 2000, 14

Ken

Senior Level III
USA,
Joined Jan 2000
14
05:54 Jun-13-2001
Re: ASNT's SNT-TC-1a
Though an ASME Inspector has a wide range of discrestion when it comes to what he will and will not accept, SNT-TC-1a is a guideline which has no mandatory requirements. It is to be used only in the development of a company "Written Practice" which in turn becomes the mandatory document. As long as the item is addressed in your "Written Practice" and is based on the guidelines of TC-1a, it should be acceptable but as you know Rule #1 "The customer (or in this case the Inspector) is always right." Good luck!

: We have a bit of a discussion at the moment on the interpretation
: of the SNT-TC-1a. According to the document, people wishing to
: become a UT level II operator, should sit a specific examination with
: a minimum of 20 questions "addressing the equipment, operating procedures
: and NDT techniques that the individual may encounter during specific
: assignments..". Our staff work to several codes and standards. Does
: this mean they have to sit an exam with 20 questions on each standard
: or procedure or is it sufficient to cover different codes and standards
: in the questions. By example 5 questions on German standards, 5 on Dutch,
: 5 on ASME etc? Is there a minimum of questions on the standards at all,
: because the 20 questions should also cover the equipment etc?
.
: Talking to some collegues this appears to be an issue for more training
: institutes and NDT companies. I would therefore appreciate some advise
: on the above.
.
: Thanks,
.
: Jan Verkooijen
.



 
 Reply 
 

Product Spotlight

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window