where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

TecScan Systems
We offer a complete line of NDT scanners, Immersion Tanks & Gantry systems which incorporate Ultrasonic, Phased Array & Eddy Current technologies.
382 views
Technical Discussions
Kelly Schauf
Kelly Schauf
08:13 Aug-18-1998
Non destructive isolation of PC-mount Transformer short

To the forum:

Currently, I am testing a printed-circuit-board-mount transformer.
There is one primary winding and three secondary windings.
There are two powdered-iron 'E' cores that are epoxied
together around the bobbin to provide the core for the transformer.

I have a problem where the inductance and the Q of the primary coil
drop way below normal past 1500 Hz with a signal of 100millivolts AC
applied. I suspect that there is a shorted turn of wire that may be causing
this.

Generally, there is maybe 1000+ turns of wire on the transformer, and the
chances of finding a marginal short-circuit with merely a microscope and
the eyes is a 'needle-in-a-haystack' type of chance. Is there some
method that would incorporate an electrical signal that would enable me
to find a short-circuit in the primary winding?

Any and all ideas are welcome. Questions are also welcome.

Regards,

Kelly Schauf


 
 Reply 
 
Jeff Nelson
Jeff Nelson
07:44 Jun-28-2000
Re: Non destructive isolation of PC-mount Transformer short
r this may help you locate how far down the line the short is.



 
 Reply 
 
Jamie Gauthier
Jamie Gauthier
09:33 Jul-01-2000
Re: Non destructive isolation of PC-mount Transformer short
In response to the TDR message post. Time Domain Reflectometer works well
but has several disadvantages. The instrument works well as long as you
have the mininum length of cable to measure. TDR's have a dead zone. This
dead zone can range from 25 to 50 feet (plus or minus depending on the
quality of your instrument.) Do you have another transformer with an equal
number of turns? If so then you can reference the value of one against the
other using a TDR. The TDR I have been using lately has an error of + or -
1% of the total length of the cable. When you are dealing with transformers
this is very large and usually unaccpetable. Once you find the short then
what? Are you equipped to hand wind it? Good luck with you
trouble-shooting. Regards,


Jamie Gauthier
Field Service Electronics Technician
Toll Free: 800-661-0066
Fax: 780-440-2538
Cell: 780-940-3427
Pager: 780-431-7470
E-mail: jgauthier@rtdquality.com
Web Site: www.rtdquality.com


--------------------
: To the forum:

: Currently, I am testing a printed-circuit-board-mount transformer.
: There is one primary winding and three secondary windings.
: There are two powdered-iron 'E' cores that are epoxied
: together around the bobbin to provide the core for the transformer.

: I have a problem where the inductance and the Q of the primary coil
: drop way below normal past 1500 Hz with a signal of 100millivolts AC
: applied. I suspect that there is a shorted turn of wire that may be causing
: this.

: Generally, there is maybe 1000+ turns of wire on the transformer, and the
: chances of finding a marginal short-circuit with merely a microscope and
: the eyes is a 'needle-in-a-haystack' type of chance. Is there some
: method that would incorporate an electrical signal that would enable me
: to find a short-circuit in the primary winding?

: Any and all ideas are welcome. Questions are also welcome.

: Regards,

: Kelly Schauf




 
 Reply 
 

Product Spotlight

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window