where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

462 views
Job Offers
ALI AZIS BIN SALLEH
ALI AZIS BIN SALLEH
18:55 Jun-06-2009
UT-CROSSCHECKER-SABAH SHELL(10 YEARS EXPERIENCED AND ABOVE ONLY)

Posted by Techno Analysis Sdn Bhd
Job Location: MMHE,Pasir Gudang,Johore.MALAYSIA

Job Title : FPS NDE Specialist
Team : Gumusut –Kakap Host Construction Team
Reports to : Gumusut – NDE Lead
Work Location : Johor Bahru
From : September 2008 To: March 2011

To perform UT Crosschecks of completed welds and weld repairs in addition to welds designated by the Engineer of Record.
Carry out NDT Surveillances in all methods to ensure that there is no non–compliances arising from technicians use of the approved procedures.
Assist in training with Contractors NDE Technicians to ensure compliance to Principals specifications and ensure that technicians improve their overall competency and ability.
Work with technicians on a one to one basis on-site to improve technicians overall competency and ability.
Monitor Contractor’s NDT equipment calibration practices and applied field examination techniques and validate contractor’s reported NDT results and NDE key performance indicators.

NDE Specialist Responsibilities:
• Familiarize self with Project NDE specifications, requirements and recommended practices (i.e. API and AWS).
• Provide input on NDE methods, procedures, processes and techniques.
• Provide feedback on approval of Contractor’s NDE personnel after witnessing field performance application and identify weaknesses through monitoring and crosschecking and carry out one to one training in order to improve level of competency of Contractors NDE techs.
• Monitor the set up, application and results of Non-Destructive testing by Contractor.
• Monitor calibration of equipment, and review certification data of personnel and equipment.
• Perform routine checks to ensure NDE techniques and methods are uniform and consistent throughout all aspects in testing and verification of welded works.
• Carry out UT cross checking, RT film review, NDE Surveillances and review of NDE records produced by the Contractor.
• Assist in the location of percentage and random NDE examinations on a daily basis in the field.
• Monitor Contractor recording of NDE examinations performed and test results; including weld repairs.
• Provide input on Contractor’s Weld Maps and NDE Identification scheme field application and traceability effectiveness.
• Prepare list of outstanding NDE for inclusion in final punch list.

Qualification & Experience

• Ultrasonic Inspection – shall be qualified to a minimum of Level II by a Certification body such as PCN or by an Employers Written Practice in accordance with SNT-TC-1A (or equivalent).

• Radiographic Interpretation – shall be qualified to a minimum of Level II by a Certification body such as PCN or by an Employers Written Practice in accordance with SNT-TC-1A (or equivalent).

• A Level II qualification in or at least a sound knowledge of MPI/PT.

• Experience – should have a minimum of ten years experience in NDE associated with Offshore Oil and Gas projects.

• Be able to specialize in the detailed examination of weldments (TKY, Cruciform, T-joints, Y-joints and single and double-sided joints etc), development of relevant Procedures and Techniques, including but not limited Magnetic Particle Inspection, Liquid Penetrant Inspection, Radiographic Interpretation and Ultrasonic Inspection.

• Be familiar with defect types associated with different welding methods.

• Recognize the problems that are associated with welding in areas of high restraint (repairs) and the defects that are typical in these locations.

• Have past experience in offshore construction yards, preferably as a Clients Crosschecker.

• Past experience working on TLP/FPS or similar Semi Submersible vessels.

• A knowledge of the following codes and publications as a minimum; AWS D1.1 Structural Code, API-RP2X Recommended Practices for UT and MT and also SNTC-TC-1A and PCN qualification requirements.

• Familiar with Welding and Inspection practices, Fabrication Specifications and Fabrication sequences in order to identify any potential NDE problems that may arise from the methods applied during production.

• NDE experience working with various materials including welding to castings and the various techniques and associated defects.

• Be fluent in English language and must be a good communicator as the job entails interacting with contractor NDE personnel.

• Strong documentation skills required.

• Competent in the review of NDE Reports and records.

• Competent computer skills in Microsoft Office products including Word and Excel

 
 

Product Spotlight

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Magnetic X-Ray Pipeline Crawler 6''-60''

Suitable to work in 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometer
...
s and provide the efficient inspection of the pipeline.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window