where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1447 views
Technical Discussions
Vikram
NDT Inspector, - Phased Array Specialist
Mistras Group Inc., USA, Joined Jun 2009, 9

Vikram

NDT Inspector, - Phased Array Specialist
Mistras Group Inc.,
USA,
Joined Jun 2009
9
01:48 Jun-27-2009
Minimum Thickness for Process Piping Inspection with UT

I have been trying to get some information on the minimum thickness that can be inspected with UT for new construction of process piping and no literature seems to point clearly to this limitation. Can anyone help me out?

Regards,
Vikram

 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 283

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
283
15:34 Jun-28-2009
Re: Minimum Thickness for Process Piping Inspection with UT
In Reply to Vikram at 01:48 Jun-27-2009 (Opening).

Vikram

not sure your question explains your problem. We can do UT on ultra thin sections such as silicon wafers in micrchips - ultimately the minimum thickness is guided by equipment, frequencies, wave modes. application and costs. In process piping all too often people define the minimum thickness they can measure based on what equipment (often transducers) they have available and not based on what they could do if they obtained the right equipment and technique. We find many people claiming that they cannot do less than 5 mm (I encountered this only the other week) however give them the correct transducer and set up and suddenly they can do 1.5 mm. You need to define what you need to measure, develop the correct set up and then see if it can be performed properly and effectively in the field.

 
 Reply 
 
Michael Moles †2014 *1948
, Joined ,
16:54 Jun-28-2009
Re: Minimum Thickness for Process Piping Inspection with UT
In Reply to John O'Brien at 15:34 Jun-28-2009 .

... and material. Many materials do not allow higherfrequencies, so this will effectively limit the thickness you can inspect.

 
 Reply 
 
Vikram
NDT Inspector, - Phased Array Specialist
Mistras Group Inc., USA, Joined Jun 2009, 9

Vikram

NDT Inspector, - Phased Array Specialist
Mistras Group Inc.,
USA,
Joined Jun 2009
9
00:50 Jun-29-2009
Re: Minimum Thickness for Process Piping Inspection with UT
In Reply to Michael Moles †2014 *1948 at 16:54 Jun-28-2009 .

To explain more clearly, does B31.3 have a limit on the minimum thickness that can be inspected for carbon steel using shear wave? I am guessing the limitation is more geometric than anything else (weld cap). However, if the weld cap is ground flush for the inspection, does B31.3 have a limitation on the thickness that can be inspected. I know it has a limitation on the diameter that can be inspected, but thickness?

Regards,
Vikram

 
 Reply 
 

Product Spotlight

VOGT Ultrasonics awarded innovation champion

Let go of the old and try something new. VOGT convinced the jury in the 27th round of the TOP 100
...
innovation competition. Our team is very pleased to officially belong to the TOP 100 in Germany!
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window