where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
652 views
Technical Discussions
Frits Dijkstra
Frits Dijkstra
02:58 Aug-25-1998
Restrictions of TOFD

The Time Of Flight Diffraction (TOFD) method, invented in the UK in the seventies, is now being used in several countries for routine NDT of welds. A method description exists, in the form of prEN 583 part 6. In The Netherlands, acceptance criteria for weld defects detected with TOFD were recently developed in a Joint Industry project, in which a.o. plant owners, manufacturers, NDT service companies and authorities were involved.

Although TOFD has been demonstrated to offer a very good probability of detection, experts agree that the technique is connected with restrictions in flaw detectability near the surface. The extent of the "dead zone" is, as previously explained by Schlengermann and Wuestenberg on this web-forum, influenced by a.o. signal length. In addition, it appears that misalignment (hi-lo) of welds in practice may increase the influence of the dead zone. On the other hand, high-resolution transducers and software algorithms such as straightening and lateral wave removal may help, but not in all cases.

It should be kept in mind that radiography and manual (pulse echo) UT have substantial restrictions as well, which we have comfortably lived with for many years. Therefore, it seems not unreasonable that TOFD is now accepted to replace RT or manual (pulse echo) UT for selected applications. Sometimes, combinations of TOFD with other techniques such as pulse-echo UT and / or magnetic particle inspection (just like other NDT methods sometimes need) will be required to meet defect detection requirements. Equipment allowing such combined inspection (TOFD plus pulse-echo) exists, e.g. RTD Rotoscan or Combiscan or others. Such combinations, if correctly applied, can lead to very reliable NDT, because "the best of two worlds" can be combined, using one technique as a "safety net" for the other.

TOFD is an NDT technique with high potential, and it is used on an increasingly large scale. But, it is not the ultimate solution to every NDT problem.




 
 Reply 
 
Jan Verkooijen
Jan Verkooijen
07:24 Sep-23-1998
Re: Restrictions of TOFD
I would like to endorse what Mr. Dijkstra has written
here. As allready stated during my comments at the ECNDT
at Kopenhagen, and also said here by Mr. Dijkstra,
it is clear that Time Of Flight Diffraction
is not the sole answer to all NDT problems in the world.
There are applications, such as the pre-service inspection
of welds, where it has been proven that TOFD is perfectly
capable of replacing an other technique in standard applications.
There are also cases where it is advisable to supplement TOFD
with other techniques should this be necessary to assure
the safety and reliability of the component, just as we
are used to do with the exisiting NDT techniques.
To be able to determine whether/when this is necessary, and which
techniques should be chosen, we still need more objective data
on POD, false call rate, sizing capabilities etc, not only
for TOFD, but also for other NDE techniques. It is
therefore that currently an international program of work is
being prepared to produce such data, to validate acceptance criteria and to
advise on training and certification standards for TOFD.
Only if we all work towards standards which are accepted
and adhered to, we can expect TOFD to become
available to NDT professionals as another valuable
tool to assure the integrity of components in industry.

: The Time Of Flight Diffraction (TOFD) method, invented in the UK in the seventies, is now being used in several countries for routine NDT of welds. A method description exists, in the form of prEN 583 part 6. In The Netherlands, acceptance criteria for weld defects detected with TOFD were recently developed in a Joint Industry project, in which a.o. plant owners, manufacturers, NDT service companies and authorities were involved.

: Although TOFD has been demonstrated to offer a very good probability of detection, experts agree that the technique is connected with restrictions in flaw detectability near the surface. The extent of the "dead zone" is, as previously explained by Schlengermann and Wuestenberg on this web-forum, influenced by a.o. signal length. In addition, it appears that misalignment (hi-lo) of welds in practice may increase the influence of the dead zone. On the other hand, high-resolution transducers and software algorithms such as straightening and lateral wave removal may help, but not in all cases.

: It should be kept in mind that radiography and manual (pulse echo) UT have substantial restrictions as well, which we have comfortably lived with for many years. Therefore, it seems not unreasonable that TOFD is now accepted to replace RT or manual (pulse echo) UT for selected applications. Sometimes, combinations of TOFD with other techniques such as pulse-echo UT and / or magnetic particle inspection (just like other NDT methods sometimes need) will be required to meet defect detection requirements. Equipment allowing such combined inspection (TOFD plus pulse-echo) exists, e.g. RTD Rotoscan or Combiscan or others. Such combinations, if correctly applied, can lead to very reliable NDT, because "the best of two worlds" can be combined, using one technique as a "safety net" for the other.

: TOFD is an NDT technique with high potential, and it is used on an increasingly large scale. But, it is not the ultimate solution to every NDT problem.




 
 Reply 
 
Jorden
Jorden
00:38 Feb-03-2007
Osbaldo
http://forum.finddesk.org/animal-health-pet.html


 
 Reply 
 

Product Spotlight

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

MIZ®-21C: Truly Affordable Eddy Current Handheld with Surface Array Capability

Introducing MIZ-21C, the first truly affordable handheld eddy current instrument with surface array
...
capabilities. MIZ-21C can deliver fast, accurate inspections in demanding NDT applications including aerospace, oil and gas, manufacturing, and power generation. The surface array solution can reduce inspection time by up to 95% compared to traditional handheld pencil probes. The ergonomic design, long battery life, and intuitive touchscreen mean you can inspect more areas faster than ever without fatigue.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window