where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

738 views
Technical Discussions
Ramalingam
NDT Inspector,
QTech Instutitu of Nondistractive Testing, India, Joined Sep 2009, 1

Ramalingam

NDT Inspector,
QTech Instutitu of Nondistractive Testing,
India,
Joined Sep 2009
1
19:21 Sep-29-2009
what is mean by tandam echo

dear sir
i am work in forging company
some doutful question in UT what is mean by tandam echo

 
 Reply 
 
Peter Bruckner
NDT Inspector, NDT Manager
United Kingdom, Joined Jul 2008, 23

Peter Bruckner

NDT Inspector, NDT Manager
United Kingdom,
Joined Jul 2008
23
23:08 Sep-29-2009
Re: what is mean by tandam echo
In Reply to Ramalingam at 19:21 Sep-29-2009 (Opening).

Hi Ramalingam,
Usually tandem testing involves 2 identical shear wave probes facing the same direction on the surface of the bar a fixed distance apart. The distance between the probes is 1/2 skip, for 45 degree probe that is the thickness or diameter of the bar under test.
The only type of defect this will find is a planar one transverse to the beam at 1/2 thickness/diameter. The test standard usually consists of a flat bottomed hole drilled in the end of the bar.

I hope this is of some assistance.
Regards
Peter

 
 Reply 
 
Uli Mletzko
R & D, Retired
Germany, Joined Nov 1998, 89

Uli Mletzko

R & D, Retired
Germany,
Joined Nov 1998
89
11:44 Sep-30-2009
Re: what is mean by tandam echo
In Reply to Peter Bruckner at 23:08 Sep-29-2009 .

Hi Peter and Ramalingam,

the expression 'tandem' originates from a bicycle type for two persons, where the second person is sitting behind the first, both looking into the forward direction, and both pedaling.

In UT the distance between the two probes is not limited to 1/2 skip, but usually ist smaller than full skip. In testing of medium and heavy wall nuclear components, tandem is a standard system at least in Germany. We have arrangements of e.g. 3, 4 or 5 or more probes, each behind the other. Usually one probe acts as transmitter, the other ones as receivers. All sound pathes are reflecting on the surface opposite to the probe system, so in general you can inspect only components with parallel or coaxial surfaces. Using more than two probes will split the cross section to be inspected into several layers.

The presumed defects at tandem UT are not transverse to the sound beam, but perpendicular to the surface.

As far as I can remember, tandem UT was invented about 1970 by the German institutes and companies BAm and/or AEG, MAN and Siemens.

Regards
Uli Mletzko (retired, from MPA/University of Stuttgart/Germany)

 
 Reply 
 

Product Spotlight

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window