where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
690 views
Technical Discussions
Ramalingam
NDT Inspector,
QTech Instutitu of Nondistractive Testing, India, Joined Sep 2009, 1

Ramalingam

NDT Inspector,
QTech Instutitu of Nondistractive Testing,
India,
Joined Sep 2009
1
19:21 Sep-29-2009
what is mean by tandam echo

dear sir
i am work in forging company
some doutful question in UT what is mean by tandam echo

 
 Reply 
 
Peter Bruckner
NDT Inspector, NDT Manager
United Kingdom, Joined Jul 2008, 21

Peter Bruckner

NDT Inspector, NDT Manager
United Kingdom,
Joined Jul 2008
21
23:08 Sep-29-2009
Re: what is mean by tandam echo
In Reply to Ramalingam at 19:21 Sep-29-2009 (Opening).

Hi Ramalingam,
Usually tandem testing involves 2 identical shear wave probes facing the same direction on the surface of the bar a fixed distance apart. The distance between the probes is 1/2 skip, for 45 degree probe that is the thickness or diameter of the bar under test.
The only type of defect this will find is a planar one transverse to the beam at 1/2 thickness/diameter. The test standard usually consists of a flat bottomed hole drilled in the end of the bar.

I hope this is of some assistance.
Regards
Peter

 
 Reply 
 
Uli Mletzko
R & D, Retired
Germany, Joined Nov 1998, 89

Uli Mletzko

R & D, Retired
Germany,
Joined Nov 1998
89
11:44 Sep-30-2009
Re: what is mean by tandam echo
In Reply to Peter Bruckner at 23:08 Sep-29-2009 .

Hi Peter and Ramalingam,

the expression 'tandem' originates from a bicycle type for two persons, where the second person is sitting behind the first, both looking into the forward direction, and both pedaling.

In UT the distance between the two probes is not limited to 1/2 skip, but usually ist smaller than full skip. In testing of medium and heavy wall nuclear components, tandem is a standard system at least in Germany. We have arrangements of e.g. 3, 4 or 5 or more probes, each behind the other. Usually one probe acts as transmitter, the other ones as receivers. All sound pathes are reflecting on the surface opposite to the probe system, so in general you can inspect only components with parallel or coaxial surfaces. Using more than two probes will split the cross section to be inspected into several layers.

The presumed defects at tandem UT are not transverse to the sound beam, but perpendicular to the surface.

As far as I can remember, tandem UT was invented about 1970 by the German institutes and companies BAm and/or AEG, MAN and Siemens.

Regards
Uli Mletzko (retired, from MPA/University of Stuttgart/Germany)

 
 Reply 
 

Product Spotlight

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window