where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

841 views
Technical Discussions
Mark
Mark
20:13 Oct-20-2009
Cladding Question

Hi All,

Basically I have an interview on Friday and I know they are having a problem welding inconnel to carbon steel (I don't know the grades, but they are to be used off shore and sub sea), they are having up to 5% dilution problems with the inconnel.

Has anyone ever come across this or a similar problem?

It would be a good topic to talk about at the interview and i'm struggling to find anything from the web

Mark

 
 Reply 
 
Roger Duwe
NDT Inspector, API-510, 570, 653
MISTRAS, USA, Joined Jan 2009, 148

Roger Duwe

NDT Inspector, API-510, 570, 653
MISTRAS,
USA,
Joined Jan 2009
148
20:44 Oct-20-2009
Re: Cladding Question
In Reply to Mark at 20:13 Oct-20-2009 (Opening).

5% dilution sounds like a submerged-arc SAW overlay. A 'colder' weld process will decrease the dilution. I would try GMAW / MAG in the short-circuiting mode. It has the least penetration, and thus least dilution, of the common welding processes.

 
 Reply 
 
Mark
Mark
21:06 Oct-20-2009
Re: Cladding Question
In Reply to Roger Duwe at 20:44 Oct-20-2009 .

Hi Roger,

Yeah they are using sub arc (I should have said before). They make sub surface christmas trees and apparently spent a fortune on getting 4 very expensive machines so I would imagine they will try like hell to make them viable.

I've only seen pictures of these christmas trees, so i'm not sure if they used MAG and then got these machines to help with the work load or had old sub arc machines there and replaced them.

Not used much sub arc, could polarity be a factor? ie using AC instead of DC?

 
 Reply 
 
Roger Duwe
NDT Inspector, API-510, 570, 653
MISTRAS, USA, Joined Jan 2009, 148

Roger Duwe

NDT Inspector, API-510, 570, 653
MISTRAS,
USA,
Joined Jan 2009
148
15:40 Oct-21-2009
Re: Cladding Question
In Reply to Mark at 21:06 Oct-20-2009 .

AC is an excellent idea. Hopefully, the new machines have that option.

SAW is run DC-Electrode Positive, putting the bulk of the heat on the wire [and flux pile]. Going to DC-Electrode Negative would put the bulk of the heat onto the base metal, a VERY bad idea. I expect that this would more than double the dilution rate.

 
 Reply 
 

Product Spotlight

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

Echomac® PA Tube Weld Tester

The new robotic Echomac® PA TW is an operator friendly test system for detecting weld zone defects
...
in tube and pipe caused by scarfing or welding processes. Electronic scanning ensures that the entire weld zone is covered without the need for mechanical movement or operator adjustment.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window