where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1023 views
Technical Discussions
anjafo
NDT Inspector
Norway, Joined Aug 2009, 204

anjafo

NDT Inspector
Norway,
Joined Aug 2009
204
11:25 Oct-28-2009
ndt of cladding

Hi,
I have some experience with this. Usually the cladding has been used to build up a seal face before machining.

After machining we perform MPI or DPI checking for defects. Here we almost always find indications in the bond/fusion area between parent material and new cladding material. Both methods show indications. Usually a light machining will remove the indication but generally as its a seal area and been machined down this is not welcome by customer. You can actually see the fused line very well after machining.

Does anyone have experience on what is causing these indications?

Its an expensive process, welding, machining, checking etc so its difficult to just tell customers there is an rejectable indication and leave. Also difficult to leave indications in the item unidentified.



I have also done UT to check fusion between parent and weld materials sometimes but the item needs to be correct geometry for this.

I know wall thickness can be checked by different methods also.

 
 Reply 
 
Phil
NDT Inspector, Radiation Safety
BINDT, MIAQP, United Kingdom, Joined Mar 2009, 151

Phil

NDT Inspector, Radiation Safety
BINDT, MIAQP,
United Kingdom,
Joined Mar 2009
151
20:33 Nov-01-2009
Re: ndt of cladding
In Reply to anjafo at 11:25 Oct-28-2009 (Opening).

Hi Anjafo,

I have also done some work on what you call cladding, we have called Buttering, I am sure it is know by other names, I have done MT and PT, on it.

I would say lack of cleaning between runs, would leave slag behind and as so ypur indication

Regards,

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 850

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
850
22:02 Nov-03-2009
Re: ndt of cladding
In Reply to anjafo at 11:25 Oct-28-2009 (Opening).

Anjafo,

Were I used to work, we did this on Steam Generators tube sheets. We did sometimes have problems and it was always related to the welding process. But we didn't experience the type of defect that you are experiencing. I suggest maybe to have your welding engineer review the procedure and change some of the parameters such a rate of deposit and your amperage.

 
 Reply 
 
anjafo79
NDT Inspector
Norway, Joined Aug 2009, 204

anjafo79

NDT Inspector
Norway,
Joined Aug 2009
204
11:01 Nov-04-2009
Re: ndt of cladding
In Reply to Michel Couture at 22:02 Nov-03-2009 .

I am going to try get a picture of the next one we test. Will take a little time though.

Problem is indication appears with DPI also.

 
 Reply 
 

Product Spotlight

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window