where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

3945 views
Technical Discussions
anjafo
NDT Inspector
Norway, Joined Aug 2009, 204

anjafo

NDT Inspector
Norway,
Joined Aug 2009
204
00:10 Nov-05-2009
Eddy Current V's DPI/MPI

Would Eddy Current find everything DPI/MPI could?

 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 307

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
307
08:30 Nov-05-2009
Re: Eddy Current V's DPI/MPI
In Reply to anjafo at 00:10 Nov-05-2009 (Opening).

Hi Anjafo,
In theory, Eddy Current should find everything that DPI or MPI will, but there are certain limitations.

MPI is field direction sensitive, so you need to be certain that you have covered the component or area with crossing magnetic fields.
The same is applicable to Eddy Current. This will not easily detect a crack when the probe runs along the length of the crack, so once again, you need to double inspect at right angles to the first inspection to be certain of detecting the cracks.

Also when it comes to borderline defect dimensions, there are some limitations.
In a laboratory environment with experimental Eddy Current equipment, we have been sucessful in reliably detecting cracks of 0.020mm deep, whilst with a very sensitive penetrant or magnetic test, detection of smaller defects could be possible. Here however surface finish is critical for all three methods.

Eddy current can also detect defects under a thin non-conductive coating (like MT, but unlike PT).

Regards,

Godfrey

 
 Reply 
 
Jim Draper
Consultant, ASNT Level III MT PT RT VT
Draper NDT, USA, Joined Jul 2009, 99

Jim Draper

Consultant, ASNT Level III MT PT RT VT
Draper NDT,
USA,
Joined Jul 2009
99
20:32 Nov-05-2009
Re: Eddy Current V's DPI/MPI
In Reply to Godfrey Hands at 08:30 Nov-05-2009 .

DPI will is not limited to electricaly conductive material. Also, I have used direct current fluorescent MPI to locate flaws 1/4" deep. Of course that is limited to ferromagnetic material, while eddy current can be used to test other electricaly conductive materials.

 
 Reply 
 

Product Spotlight

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window