where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1034 views
Technical Discussions
aldo
Engineering
Italy, Joined Jan 2009, 39

aldo

Engineering
Italy,
Joined Jan 2009
39
12:04 Dec-05-2009
performance mercury vapour lamp

Hi everibody...
I readed the parameters that have influence on life mercury vapor lamp...They are:
voltage fluctutations, dirt on filters, tarnishing of reflectors, etc..
The question is:
Can have influence the type or the quality of the isotope mercury uses in lamps?
I do not read nothing on this issue and i want the your opinion if is possible..
tanks and best regards

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 893

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
893
15:36 Dec-05-2009
Re: performance mercury vapour lamp
In Reply to aldo at 12:04 Dec-05-2009 (Opening).

Aldo,

I think what we are looking at here are the factors that will affect the longivity and the detectability of defect using a Black Light. Anything that is inside the glass shell is out of your control. Not only that, those lamps were manufactured according to a proven and quality control process.

What is important for us in regards to MT or PT is that the lamp be clean to allow maximum light emission therefore increasing your chance of detection. Also, dirt on the lamp and or on the filter also decreases its life because of the hot spots that it will create on its surface. It may results in a filter cracking for example, which could be dangerous for anyone that happen to be looking at the light. Mind you, why should you be looking at the light in the first place?

 
 Reply 
 
aldi
Engineering
Italy, Joined Jan 2009, 39

aldi

Engineering
Italy,
Joined Jan 2009
39
17:10 Dec-05-2009
Re: performance mercury vapour lamp
In Reply to Michel Couture at 15:36 Dec-05-2009 .

Hi michel,
I have done this question because in one quiz there was the answer where it spoke if the quality of isotope mercury has o has not any influence on quality and intensity black light and on its life...The correct answer was that on performance mercury vapour lamp was influence by type of isotope mercury....
Aldo

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 893

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
893
22:04 Dec-05-2009
Re: performance mercury vapour lamp
In Reply to aldi at 17:10 Dec-05-2009 .

Aldo,

I totally agree with you if you look at it this way. Unfortunately, some people (the ones writing those exams) seems to really like to split hair and as you can see, I don't have much to spare. But seriously, they are technically right, yet as a technician doing a PT inspection it is not something you have control over. Like I said previously, the bulb is made a certain way, under specific control in the manufacturer's plant. In other word, you get what you get. As long as you buy the buld that is design for the lamp you are using, everything should be fine. What we have control over and what will affect our inspection is what we spoke about previously ie. cleanilness of the bulb and filter. Yet that is something that I find very few technicians do.

It's not like what some people ask about UT instrument. They have rechargeable 'D' cell batteries that cost an arm and a leg from a supplier, but what appears to be the same one at a local story is a third of the price. In this case, it is different. The difference in price very often is tied in with the amperage rating. So you have a choice: a) you buy the cheap battery that will last only two hours or b) the expensive one that will last you eight hours?

 
 Reply 
 

Product Spotlight

MANTIS

MANTIS is a compact, powerful and affordable flaw detector (16:64PR), dedicated to field operators
...
. This portable equipment offers standard (electronic-, sector-, compound scan, conventional UT for pulse-echo, dual array and TOFD inspections), and advanced phased-array (real-time TFM -Total Focusing Method). MANTIS benefits from the same intuitive and user-friendly interface (CAPTURE) than Gekko for easier inspections.
>

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window