where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1036 views
Technical Discussions
aldo
Engineering
Italy, Joined Jan 2009, 39

aldo

Engineering
Italy,
Joined Jan 2009
39
12:04 Dec-05-2009
performance mercury vapour lamp

Hi everibody...
I readed the parameters that have influence on life mercury vapor lamp...They are:
voltage fluctutations, dirt on filters, tarnishing of reflectors, etc..
The question is:
Can have influence the type or the quality of the isotope mercury uses in lamps?
I do not read nothing on this issue and i want the your opinion if is possible..
tanks and best regards

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 893

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
893
15:36 Dec-05-2009
Re: performance mercury vapour lamp
In Reply to aldo at 12:04 Dec-05-2009 (Opening).

Aldo,

I think what we are looking at here are the factors that will affect the longivity and the detectability of defect using a Black Light. Anything that is inside the glass shell is out of your control. Not only that, those lamps were manufactured according to a proven and quality control process.

What is important for us in regards to MT or PT is that the lamp be clean to allow maximum light emission therefore increasing your chance of detection. Also, dirt on the lamp and or on the filter also decreases its life because of the hot spots that it will create on its surface. It may results in a filter cracking for example, which could be dangerous for anyone that happen to be looking at the light. Mind you, why should you be looking at the light in the first place?

 
 Reply 
 
aldi
Engineering
Italy, Joined Jan 2009, 39

aldi

Engineering
Italy,
Joined Jan 2009
39
17:10 Dec-05-2009
Re: performance mercury vapour lamp
In Reply to Michel Couture at 15:36 Dec-05-2009 .

Hi michel,
I have done this question because in one quiz there was the answer where it spoke if the quality of isotope mercury has o has not any influence on quality and intensity black light and on its life...The correct answer was that on performance mercury vapour lamp was influence by type of isotope mercury....
Aldo

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 893

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
893
22:04 Dec-05-2009
Re: performance mercury vapour lamp
In Reply to aldi at 17:10 Dec-05-2009 .

Aldo,

I totally agree with you if you look at it this way. Unfortunately, some people (the ones writing those exams) seems to really like to split hair and as you can see, I don't have much to spare. But seriously, they are technically right, yet as a technician doing a PT inspection it is not something you have control over. Like I said previously, the bulb is made a certain way, under specific control in the manufacturer's plant. In other word, you get what you get. As long as you buy the buld that is design for the lamp you are using, everything should be fine. What we have control over and what will affect our inspection is what we spoke about previously ie. cleanilness of the bulb and filter. Yet that is something that I find very few technicians do.

It's not like what some people ask about UT instrument. They have rechargeable 'D' cell batteries that cost an arm and a leg from a supplier, but what appears to be the same one at a local story is a third of the price. In this case, it is different. The difference in price very often is tied in with the amperage rating. So you have a choice: a) you buy the cheap battery that will last only two hours or b) the expensive one that will last you eight hours?

 
 Reply 
 

Product Spotlight

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window