where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Iris Inspection Services, Inc.
We are the world's largest supplier of air cooler, boiler and exchanger tubing inspection services.

949 views
Career Discussions
Rafid O. López
Rafid O. López
00:48 Jan-09-2010
information about penetrant testing

Anyone has information about penetrant testing?? I need present the level III examination in PT.

Thanks.

Best regards.

 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
02:02 Jan-09-2010
Re: information about penetrant testing
In Reply to Rafid O. López at 00:48 Jan-09-2010 (Opening).

You need to get the ASNT recommended study material or go through the various NDT handbooks and also refresh your basic physics of penetrant testing. If you are a level II, you already have about 70% of what you need. If you are planning to directly go for level III exam, you need graduate level preparation.

Best wishes.

 
 Reply 
 
aldo
Engineering
Italy, Joined Jan 2009, 39

aldo

Engineering
Italy,
Joined Jan 2009
39
12:21 Jan-09-2010
Re: information about penetrant testing
In Reply to S.V.Swamy at 02:02 Jan-09-2010 .

Hi lopez...
The answer Mr.swamy is correct...Infact there is not more different between ii level and iii level...
From the point of view on basic theory there are not different (capillary force,wetty ability etc...)
There are some different on metallurgy matter and on procedure menagement of the personal NDT (example NAS, EN, etc). Infact the III level has the totally menagement of CND Aldo

 
 Reply 
 
Rafid O. López
Rafid O. López
16:26 Jan-11-2010
Re: information about penetrant testing
In Reply to aldo at 12:21 Jan-09-2010 .

You are right. I pass the basic examination from ASNT, but I could not pass the pt examination.

I have some material about NDT from ASNT, but a lot information of the study guides, are not in the examination.

I was level II, now i´m an engineer NDT, in aerospace in Queretaro, Mexico.

Best regards.

 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Wireless TOFD scanner

Quick, accurate and highly reproducible welds testing. The System operates wirelessly and is compat
...
ible with any type of Windows based Laptop, Desktop or Tablet.
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window