where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Iris Inspection Services, Inc.
We are the world's largest supplier of air cooler, boiler and exchanger tubing inspection services.
3785 views
Technical Discussions
Mulianto Sinaga
NDT Inspector, -
-, Indonesia, Joined Sep 2009, 4

Mulianto Sinaga

NDT Inspector, -
-,
Indonesia,
Joined Sep 2009
4
14:38 Feb-06-2010
yoke pole spacing

Dear all,

I want to know what's the affect of pole spacing of yoke if I open the pole too close?

 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 305

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
305
14:55 Feb-06-2010
Re: yoke pole spacing
In Reply to Mulianto Sinaga at 14:38 Feb-06-2010 (Opening).

Hi Mulianto,
If you open the poles up too far, then the magnetic field between the poles may not be enough to detect the cracks you need to find.
If you keep them too close together, there are two risks
1. You will get a smaller coverage, so need to test next test much closer
2. You may saturate with magnetism and cause too big a background to see cracks.

That's a very simple explanation. Hope it helps.

Godfrey

 
 Reply 
 
Jim Draper
Consultant, ASNT Level III MT PT RT VT
Draper NDT, USA, Joined Jul 2009, 99

Jim Draper

Consultant, ASNT Level III MT PT RT VT
Draper NDT,
USA,
Joined Jul 2009
99
17:23 Feb-06-2010
Re: yoke pole spacing
In Reply to Godfrey Hands at 14:55 Feb-06-2010 .

Mulianto,

I use a Parker DA 200 probe. My manual recomends 5 to 6 inches between the legs. Here is a link to a PDF of the manual. I hope this helps.

http://www.parkreshcorp.com/pdfopinstr/DA200.pdf

 
 Reply 
 
ezio
Other, Retired ex Laboratory Technical Manager
OMECO Research Centre, Italy, Joined Sep 2008, 275

ezio

Other, Retired ex Laboratory Technical Manager
OMECO Research Centre,
Italy,
Joined Sep 2008
275
20:28 Feb-06-2010
Re: yoke pole spacing
In Reply to Mulianto Sinaga at 14:38 Feb-06-2010 (Opening).

You can see the effect with a simple specimen: a plate 50x250x20 mm with a subsurface 1-1,5 mm hole on the side. Good look, ciao, ezio

 
 Reply 
 
rama
NDT Inspector, -
Kuwait, Joined Jan 2010, 13

rama

NDT Inspector, -
Kuwait,
Joined Jan 2010
13
08:59 Feb-07-2010
Re: yoke pole spacing
In Reply to Mulianto Sinaga at 14:38 Feb-06-2010 (Opening).

Pole spacing too close means the magnetic field between the the poles will be greater and it leads to non relevant indications named as banding.

 
 Reply 
 
RENATO BANAGA
Engineering,
Philippine Nuclear Research Institute (PNRI), Philippines, Joined Jul 2005, 8

RENATO BANAGA

Engineering,
Philippine Nuclear Research Institute (PNRI),
Philippines,
Joined Jul 2005
8
11:24 Feb-08-2010
Re: yoke pole spacing
In Reply to rama at 08:59 Feb-07-2010 .

Hi, Mulianto,

Making your Yoke pole spacing too close will create too much sensitivity due to the increase in the magnetic field strenght and that creates unnecessary indications. On the otherhand, making your pole spacing too far would provide lesser magnetic field strenght (lesser sensitivity).
So it is better for you to established your own correct pole spacing by doing some experimentation using same material of the same thickness with a known artificial defect and with that you can make your own appropriate MT procedure.

Renato Banaga

 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window