where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1080 views
Technical Discussions
junho
NDT Inspector,
KOREA Material INSPECTION, South Korea, Joined Oct 2009, 21

junho

NDT Inspector,
KOREA Material INSPECTION,
South Korea,
Joined Oct 2009
21
14:22 Feb-19-2010
creeping wave methode

hi all

I wondering, Is ASME explaining creeping wave method
for ID deadzone inspect

thank you

 
 Reply 
 
Carlos Correia
R & D, - -
UCV & EGROUP, Venezuela, Joined Oct 2008, 120

Carlos Correia

R & D, - -
UCV & EGROUP,
Venezuela,
Joined Oct 2008
120
19:05 Feb-19-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Hello Junho, CW Method is still beyond ASME considerations. You should to check the 2007 edition. But you can write to Ed Ginzel or to Mark Davis. They are part of this forum and is sure they know...

 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1282

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1282
19:09 Feb-19-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Mr Park
ASME does not describe the "so-called" creeping wave. When you examine the arrival times of the signals when peaking a small depth notch on the opposite wall it will be seen that the detection is actually achieved by the shear headwave. This can be done using a refracted compression mode at some angle between about 70° to 80°
Good description can be found on the application of the techniques in general on http://www.ndt.net/article/pow1297/schmid/schmid.htm

 
 Reply 
 
andrew cunningham
NDT Inspector
Canada, Joined Jun 2008, 238

andrew cunningham

NDT Inspector
Canada,
Joined Jun 2008
238
23:55 Feb-22-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Download Mode Change, Creeping Wave or Corner Trap???

Hi Junho

Please find attachment that may explain acoustics of an ID connected reflector.
I hope it helps you.

Yours sincerely
Andrew
 
 Reply 
 

Product Spotlight

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

FAAST-PA! OEM Patented phased Array for high speed UT inspection

Multiangle, Multifocus, Multifrequency, Multibeam. Instead of stacking UT electronics and having m
...
any PA probes, FAAST-PA is able to transmit all delay laws within ONE single shot in Real time.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window