where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1098 views
Technical Discussions
junho
NDT Inspector,
KOREA Material INSPECTION, South Korea, Joined Oct 2009, 21

junho

NDT Inspector,
KOREA Material INSPECTION,
South Korea,
Joined Oct 2009
21
14:22 Feb-19-2010
creeping wave methode

hi all

I wondering, Is ASME explaining creeping wave method
for ID deadzone inspect

thank you

 
 Reply 
 
Carlos Correia
R & D, - -
UCV & EGROUP, Venezuela, Joined Oct 2008, 120

Carlos Correia

R & D, - -
UCV & EGROUP,
Venezuela,
Joined Oct 2008
120
19:05 Feb-19-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Hello Junho, CW Method is still beyond ASME considerations. You should to check the 2007 edition. But you can write to Ed Ginzel or to Mark Davis. They are part of this forum and is sure they know...

 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1286

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1286
19:09 Feb-19-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Mr Park
ASME does not describe the "so-called" creeping wave. When you examine the arrival times of the signals when peaking a small depth notch on the opposite wall it will be seen that the detection is actually achieved by the shear headwave. This can be done using a refracted compression mode at some angle between about 70° to 80°
Good description can be found on the application of the techniques in general on http://www.ndt.net/article/pow1297/schmid/schmid.htm

 
 Reply 
 
andrew cunningham
NDT Inspector
Canada, Joined Jun 2008, 238

andrew cunningham

NDT Inspector
Canada,
Joined Jun 2008
238
23:55 Feb-22-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Download Mode Change, Creeping Wave or Corner Trap???

Hi Junho

Please find attachment that may explain acoustics of an ID connected reflector.
I hope it helps you.

Yours sincerely
Andrew
 
 Reply 
 

Product Spotlight

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

FAAST-PA! OEM Patented phased Array for high speed UT inspection

Multiangle, Multifocus, Multifrequency, Multibeam. Instead of stacking UT electronics and having m
...
any PA probes, FAAST-PA is able to transmit all delay laws within ONE single shot in Real time.
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window