where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1971 views
Technical Discussions
Juan Amado
Engineering, Inspection
Arco Industrial, S.A., Panama, Joined Nov 2001, 44

Juan Amado

Engineering, Inspection
Arco Industrial, S.A.,
Panama,
Joined Nov 2001
44
23:48 Feb-25-2010
USM Go

I was practicing drawing a DAC curve with my new USM Go, but cannot erase it by the procedure shown in the instructions, anybody have this same issue?
Best regards,
Juan Amado

 
 Reply 
 
Phanindra Kumar
Phanindra Kumar
13:19 Feb-26-2010
Re: USM Go
In Reply to Juan Amado at 23:48 Feb-25-2010 (Opening).

Dear Amado,

Please recall the DAC/TCG curve which you stored. Go to DAC/TCG option, select SETUP menu. You will find a DELETE CURVE showing as . If you want to delete DAC curve, push joystick Left or Right after that press Function1+Function2 buttons at a time.

I think you will get the result, which you are looking for.

Can you please confirm, is that the above procedure have you followed?

Best Regards
Phanindra Kumar.M

 
 Reply 
 
marshall
marshall
04:59 Aug-14-2014
Re: USM Go
In Reply to Phanindra Kumar at 13:19 Feb-26-2010 .

I was trying to change from dual to multi mode and it would not allow until I deleted dac curve. I have tried procedures in manual and nothing has worked.

 
 Reply 
 
Marshall
Marshall
06:18 Aug-14-2014
Re: USM Go
In Reply to Phanindra Kumar at 13:19 Feb-26-2010 .

Ok yes, pressing the F1 and F2 button does delete the curve but when you realize the following.
DMS go the F1 and F2 buttons are both on the top toggles with F3 F4 on bottom.
USM go the F1 and F2 buttons are both on the bottom toggles with gain on top.
A three hour frustration trip depending on which mode you have become comfortable with first.
Don't think I will tell anyone else at the shop about this.. Why take all the fun out of it for them.
LOL

 
 Reply 
 

Product Spotlight

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window