where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

2416 views
Technical Discussions
hemant suthar
hemant suthar
09:21 Mar-03-2010
regarding asme sec-ix group no.

what is the purpose of group no. in asme sec-ix and on what base it classified.

 
 Reply 
 
Roger Duwe
NDT Inspector, API-510, 570, 653
MISTRAS, USA, Joined Jan 2009, 148

Roger Duwe

NDT Inspector, API-510, 570, 653
MISTRAS,
USA,
Joined Jan 2009
148
18:05 Mar-04-2010
Re: regarding asme sec-ix group no.
In Reply to hemant suthar at 09:21 Mar-03-2010 (Opening).

Mr. Suthar, if you mean Group# [versus P#], the Group#'s are subsets of the P#'s that group materials with similar heat-input and heat-treatment characteristics, per ASME Section IX.
Group# is a Supplementary Essential Variable, and is used for controlled heat input Weld Procedures, like when the Impact Strength at Low Temperature is being tested and recorded during the Procedure Qualification.

 
 Reply 
 
Ganesh V
Other, Site Inspection Supervisor
PDO,Oman, India, Joined Jun 2013, 5

Ganesh V

Other, Site Inspection Supervisor
PDO,Oman,
India,
Joined Jun 2013
5
07:19 Jun-07-2013
Re: regarding asme sec-ix group no.
In Reply to hemant suthar at 09:21 Mar-03-2010 (Opening).

Group Numbers are assigned additionally to P-Numbers. These Group Numbers classify the metals within P-Numbers for the purpose of procedure qualification where notch-toughness ( Charpy V-notch impact test ) requirements are specified.
( Refer : QW.200.3 )

So, whenever the codes requires Impact testing, WPS shall specify the Supplimentary essential variables also, and PQR shall reflect the actual p Number's and its applicable Group Numbers, any changes after in WPS need to be requalified with a PQR again.

 
 Reply 
 
Nelson
Nelson
14:21 Sep-18-2013
Re: regarding asme sec-ix group no.
In Reply to Roger Duwe at 18:05 Mar-04-2010 .

Dear Roger Duwe,

Good info you give. How can i refer that it is related with "similar heat input & heat treatment characteristics" in code. i.e, any asme state these group number has been classified according to this? Please reply.
Thanks in advance.

Neo.

 
 Reply 
 
Roger D. Duwe
NDT Inspector, API-510, 570, 653
MISTRAS, USA, Joined Jan 2009, 148

Roger D. Duwe

NDT Inspector, API-510, 570, 653
MISTRAS,
USA,
Joined Jan 2009
148
19:38 Sep-18-2013
Re: regarding asme sec-ix group no.
In Reply to Nelson at 14:21 Sep-18-2013 .

Nelson, that is so basic that the answer is almost hard. This info comes from the definition of "P#" and "Group#". It is part of the foundation of ASME Sect IX. Without it, every different material spec & grade would require its own individualized PQR and WPS.

 
 Reply 
 

Product Spotlight

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window